Results 41 to 50 of about 189,211 (301)

Composition Analysis of Cocoa Butter by Differential Scanning Calorimetry

Техника и технология пищевых производств
Consumer properties of chocolate depend largely on the quality of cocoa butter, which affects the technological processes of chocolate production. This article introduces a new method of calorimetry-based mathematical modeling applied to polymorphic ...
Sergey A. Bredikhin, Vladimir N. Andreev, Anastasia P. Nazarova, Igor A. Korotkiy   +3 more
doaj   +1 more source

Phase separation phenomena in solutions of cellulose acetate. I. Differential scanning calorimetry of cellulose acetate in mixtures of dioxane and water [PDF]

, 1981
The nature and kinetics of phase separation processes of solutions of cellulose acetate (degree of substitution, 2.5) in mixtures of dioxane and water are studied by differential scanning calorimetry (DSC).
Altena, F.W., Smolders, C.A.
core   +3 more sources

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Differential scanning calorimetry: A screening tool for the development of diacerein eutectics

Results in Chemistry, 2022
The application of DSC technique has been employed for better understanding the behavior of multi-component solid forms of poorly water-soluble drugs. Therefore, the purpose of the present work was to investigate the binary system of Diacerein (DIC) by ...
Rajeshri D. Patel, Mihir K. Raval
doaj   +1 more source

Development of Sustainable MgO–C Refractories Using MgO–C Recyclates and a Novel Eco‐Friendly Fructose–Tannin Binder Crosslinked With Citric Acid

Advanced Engineering Materials, EarlyView.
This study develops sustainable MgO–C refractories using recycled materials and eco‐friendly fructose–tannin binders. The enhanced performance of citric acid as a cross‐linker and functional additives on mechanical and thermomechanical properties was examined. Characterization included strength tests, immersion trials, and microstructural and inclusion
Dinesh K. Gunasekar, Jana Hubálková, Steffen Dudczig, Gert Schmidt, Florian Kerber, Thomas Schemmel, Patrick Gehre, Christos G. Aneziris   +7 more
wiley   +1 more source

A Novel On-chip Three-dimensional Micromachined Calorimeter with Fully Enclosed and Suspended Thin-film Chamber for Thermal Characterization of Liquid Samples [PDF]

, 2014
A microfabricated calorimeter (μ-calorimeter) with an enclosed reaction chamber is presented. The 3D micromachined reaction chamber is capable of analyzing liquid samples with volume of 200 nl. The thin film low-stress silicon nitride membrane is used to
Arpaci V. S., Benyamin Davaji, Chung Hoon Lee, Hye Jeong Bak, Woo-Jin Chang   +4 more
core   +2 more sources

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Magnetic properties of Ni2.18Mn0.82Ga Heusler alloys with a coupled magnetostructural transition

, 2002
Polycrystalline Ni2.18Mn0.82Ga Heusler alloys with a coupled magnetostructural transition are studied by differential scanning calorimetry, magnetic and resistivity measurements.
A. A. Cherechukin, A. D. Bozhko, A. N. Vasil’ev, A. N. Vasil’ev, A. Planes, A. Zheludev, E. A. Rozenberg, E. M. Levin, F. Hu, I. E. Dikshtein, J. Kübler, J. Tani, J. Worgull, K. Ullakko, Kazuko Inoue, L. Morellon, M. Matsumoto, P. J. Brown, P. J. Webster, R. Note, R. Tickle, R. Z. Levitin, R. Zach, S. Fujii, S. J. Murray, S. Kyuji, S. Plogmann, T. Castán, T. Kanomata, T. Takagi, V. A. Chernenko, V. K. Pecharsky, V. V. Khovailo   +32 more
core   +1 more source

Thermo-mechanical analysis of dental silicone polymers [PDF]

, 2006
Soft lining materials are used to replace the inner surface of a conventional complete denture, especially for weak elderly patients, with delicate health who cannot tolerate the hard acrylic denture base.
B Wunderlich, C. Lacabanne, D Buch, E. Dantras, EA Turi, F Tamura, FA Rueggeberg, H Murata, H Murata, H Murata, H Murata, J. Dandurand, JF Mccabe, JF Mccabe, K Saber-Sheikhk, KR Williams, M Braden, M Waters, M. -H. Lacoste-Ferré, M. Blandin, Ph. Demont, PS Wright, PS Wright, PS Wright, RH Baney, T Takahashi   +25 more
core   +2 more sources

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source