Results 101 to 110 of about 2,937,719 (310)

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Diffusion bonding and brazing of high purity copper for linear collider accelerator structures

Physical Review Special Topics. Accelerators and Beams, 2001
Diffusion bonding and brazing of high purity copper were investigated to develop procedures for joining precision machined copper components for the Next Linear Collider (NLC). Diffusion bonds were made over a range of temperatures from 400 °C to 1000 °C,
J. W. Elmer, J. Klingmann, K. Van Bibber
doaj   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Diffusion Bonding of Al-Mg-Si Alloy and 301L Stainless Steel by Friction Stir Lap Welding Using a Zn Interlayer. [PDF]

Materials (Basel), 2022
Dong JH, Liu H, Ji SD, Yan DJ, Zhao HX.
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions

Advanced Functional Materials, EarlyView.
DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng, Qian Yao, Yanan Sun, Hongyu Lv, Zhongchao Bai, Guoliang Zhang, Nana Wang, Jian Yang   +7 more
wiley   +1 more source

Modeling and Simulations of 4H-SiC/6H-SiC/4H-SiC Single Quantum-Well Light Emitting Diode Using Diffusion Bonding Technique. [PDF]

Micromachines (Basel), 2021
Rashid MH, Koel A, Rang T, Nasir N, Mehmood H, Cheema S.   +5 more
europepmc   +1 more source

Microstructure evolution and mechanical properties of diffusion bonding CoCrCuFeNi high entropy alloy to Inconel 600 alloy

Journal of Materials Research and Technology
In this study, the CoCrCuFeNi high entropy alloy was diffusion bonded with the Inconel 600 superalloy at bonding temperatures ranging from 950 to 1100 °C for a bonding time of 2 h under a pressure of 20 MPa in a vacuum.
Honglong Zhao, Fugui Zhou, Xuefeng Shen, Juan Li, Qingdong Qin, Jianming Wu   +5 more
doaj   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source