Results 1 to 10 of about 102,601 (297)
Journal of Magnesium and Alloys, 2020 In this study, an overcasting process followed by a low-temperature (200°C) annealing schedule has been developed to bond magnesium to aluminum alloys. ProCAST software was used to optimize the process parameters during the overcasting process which lead
Ziang Zhu +4 more
doaj +4 more sources
Constructing a Superior Interfacial Microstructure on Carbon Fiber for High Interfacial and Mechanical Properties of Epoxy Composites [PDF]
Nanomaterials, 2022 The interface quality is crucial for the properties of carbon fiber-reinforced polymer- matrix composites (CFRPs). In order to improve the interfacial and mechanical properties of CFRPs, a superior gradient modulus interfacial microstructure is ...
Ping Han +3 more
doaj +2 more sources
Modeling method and verification of interface contact stiffness based on micro-surface morphology detection. [PDF]
PLoS ONEA novel elastic-plastic theoretical calculation model for interfacial contact stiffness has been deduced and established based on the observed characteristics of the interface microstructure.
Shikun Lu, Bokai Feng, Yunshuai Chen
doaj +2 more sources
Enhanced flow sensing with interfacial microstructures [PDF]
Biosurface and Biotribology, 2020 Biological flow receptors show astonishing performance and are used as models for the design of novel flow sensors. However, the functional importance of interfacial microstructures is seldom discussed in previous review papers. Herein, this review summarises the underlying biomechanical principles in the biological flow receptors and describes the ...
Yonggang Jiang +5 more
openaire +2 more sources
Frontiers in Chemistry, 2022 In this paper, we report the construction of network-like platinum (Pt) nanosheets based on Pt/reduced graphite oxide (Pt/rGO) hybrids by delicately utilizing a calorific-effect-induced-fusion strategy.
Ting-Wen Chen +5 more
doaj +1 more source
SEM-Backscattered Imaging analysis of Cementitious Composite Matrix Incorporating Mineral Admixture [PDF]
Engineering and Technology Journal, 2014 Microstructure imaging interpretation of polished surface has become well established as a method for the study of cement and concrete microstructure. This paper is an attempt to provide micro-level examination to the microstructure of cement paste in ...
Maan S. Hassan
doaj +1 more source
Crystals, 2023 Some multi-materials produced via SLM and containing 316L steel may exhibit defects and cracks in the interfacial zone. There is a lack of research on 316L/NiTi multi-materials with an interlayer produced via SLM.
Arseniy Repnin +2 more
doaj +1 more source
Effects of impurities on alumina–niobium interfacial microstructures [PDF]
Materials Characterization, 2006 Optical microscopy, scanning electron microscopy, and transmission electron microscopy were employed to examine the interfacial microstructural effects of impurities in alumina substrates used to fabricate alumina-niobium interfaces via liquid-film-assisted joining.
McKeown, Joseph T. +3 more
openaire +2 more sources
Microstructure evolution of Ag-Cu/BaCo0.7Fe0.2Nb0.1O3-δ joints in air and argon atmospheres
Journal of Asian Ceramic Societies, 2021 Microstructure evolution of the joints formed by Ag-6.6 mol% Cu brazing BaCo0.7Fe0.2Nb0.1O3-δ (BCFN) ceramic after long-term heat treatment in different atmospheres was revealed.
Chao Zhang +6 more
doaj +1 more source
Microstructure and Mechanical Properties of Vacuum Diffusion Bonded Zr-4 Alloy Joint
Crystals, 2021 The development of welding technology for zirconium alloy has great significance on the safety, stability, and reliability of the operation of the nuclear reactor.
Zeming Wang +7 more
doaj +1 more source