Results 21 to 30 of about 587,530 (285)
Explicit models for flexural edge and interfacial waves in thin elastic plates [PDF]
, 2011 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In the thesis explicit dual parabolic-elliptic models are constructed for the Konenkov flexural edge wave and the Stoneley-type flexural interfacial wave in
Kossovich, Elena
core +7 more sources
Reactive Air Brazing of TiAl Alloy Using Ag-CuO: Microstructure and Joint Properties
Crystals, 2021 TiAl alloy was successfully brazed with Ag-CuO filler in air atmosphere under simple technical conditions. The wettability of a series of Ag-CuO fillers on TiAl was analyzed. Ag-2mol%CuO filler possessed good wetting behavior on TiAl alloy.
Haoran Yang +3 more
doaj +1 more source
Generation and characterization of T40/A5754 interfaces with lasersPatrice [PDF]
, 2014 Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum
BERTHE, Laurent +5 more
core +1 more source
Microstructure and Properties in Metals and Alloys
, 2023 Microstructure design is key in targeting the desired material’s properties. Contributions related to microstructure design and characterization are collected in this Topic, together with their relation to the mechanical, fatigue, wear and corrosion ...
core +1 more source
Assembling Hybrid Energetic Materials with Controllable Interfacial Microstructures by Electrospray [PDF]
ACS Omega, 2021 Constructing hybrid energetic materials (HEMs) consisting of nanothermites and organic high explosives is an efficient strategy to regulate the reactivity of energetic composites. To investigate the role of interfacial microstructures in determining the reactivity of HEMs, we employ electrospray, one ramification of electrohydrodynamic atomization, to ...
Lihong Chen +6 more
openaire +4 more sources
Microstructure measurements and estimates of entrainment in the Denmark Strait overflow plume [PDF]
, 2013 To examine processes controlling the entrainment of ambient water into the Denmark Strait overflow (DSO) plume/gravity current, measurements of turbulent dissipation rate were carried out by a quasi-free-falling (tethered) microstructure profiler (MSP ...
V. Paka +11 more
core +2 more sources
Results in Physics, 2019 The wettability, interfacial reaction, microstructure and hardness of Sn58Bi (SnBi) solder paste on Cu, high-temperature Cu (H-Cu) and graphene-coated Cu (G-Cu) were investigated in this study. Experimental results indicate that the wettability of Sn58Bi
Yang Liu +5 more
doaj +1 more source
Cailiao gongcheng, 2020 Zn/AZ31/Zn clad sheets were prepared by hot rolling process. The effects of annealing temperature and time on the interface microstructure and mechanical properties of the clad sheets were investigated. The results show that the annealing temperature has
XU Feng-guang +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 The Cu-GO layered composites with excellent thermal conductivity were fabricated by ultrasonic-assisted electrodeposition and ultrasonic spraying composite processes.
Fengjia Li +7 more
doaj +1 more source
Temperature dependence of the interfacial shear strength in glass-fibre epoxy composites [PDF]
, 2014 The present work focuses on further investigation of the hypothesis that a significant fraction of apparent interfacial shear strength (IFSS) in fibre-reinforced composites can be attributed to a combination of residual radial compressive stress and ...
Thomason, James, Yang, Liu
core +1 more source