Results 161 to 170 of about 678,742 (284)

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Microwave-Assisted Wet Granulation for Engineering Rice Starch-Mannitol Co-Processed Excipients for Direct Compression of Orally Disintegrating Tablets. [PDF]

Pharmaceutics
Trisopon K, Saokham P.
europepmc   +1 more source

Facilitating Expedited Drug Approval—the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, EarlyView.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Preformulation Study of Carbamazepine Orally Disintegrating Tablets for Pediatric Patients Using Direct Compression and the SeDeM Diagram Tool: A Quality by Design Approach. [PDF]

Pharmaceutics
Canadell-Heredia R, Rouaz-El-Hajoui K, Franco-Piedrahita N, Pérez-Lozano P, Suñé-Pou M, Suñé-Negre JM, García-Montoya E.   +6 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Evaluation of the Potential of Novel Co-Processed Excipients to Enable Direct Compression and Modified Release of Ibuprofen. [PDF]

Pharmaceutics
Aleksić I, Glišić T, Ćirin-Varađan S, Djuris M, Djuris J, Parojčić J.   +5 more
europepmc   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Visual impairment associated with direct compression of the visual cortex due to subdural hematoma following foramen magnum decompression: illustrative case. [PDF]

J Neurosurg Case Lessons
Nakayama Y, Yamana S, Nogami R, Fuga M, Sano T, Kawamura D, Murayama Y, Ohashi H.   +7 more
europepmc   +1 more source

A Spray-Dried, Co-Processed Rice Starch as a Multifunctional Excipient for Direct Compression. [PDF]

Pharmaceutics, 2020
Trisopon K, Kittipongpatana N, Kittipongpatana OS.   +2 more
europepmc   +1 more source