Results 91 to 100 of about 5,961 (226)

Torque Ripple Reduction and Flux-Droop Minimization of DTC With Improved Interleaving CSFTC of IM Fed by Three-Level NPC Inverter

open access: yesIEEE Access, 2019
Direct torque control (DTC) is known for its fast control in AC motor drives due to its simple control structure that directly controls the torque without the need for modulation blocks or frame transformations. However, when used in induction motor (IM)
Samer Saleh Hakami   +2 more
doaj   +1 more source

Recent Advancements in Lung Cancer Metastasis Prevention Based on Nanostrategies

open access: yesAdvanced Science, Volume 12, Issue 23, June 20, 2025.
Metastasis is the leading cause of death in patients with lung cancer. Nanomedicine can be used to prepare efficient drug delivery systems owing to their advantages and plays an important role in the synergistic antimetastasis of lung cancer. This comprehensive review summarizes the emerging nanostrategies against lung cancer metastasis based on the ...
Fan Xu   +7 more
wiley   +1 more source

Improved direct torque control using Kalman filter: application to a doubly-fed machine [PDF]

open access: yes, 2009
Direct Torque Control (DTC) has been extensively researched and applied during the last two decades. However, it has only first been applied to the Brushless Doubly Fed Reluctance Machine (BDFRM) a few years ago in its basic form inheriting its intrinsic
Chaal, Hamza, Jovanovic, Milutin
core  

An improved two-vector model predictive torque control based on RMS duty ratio optimization for pmsm [PDF]

open access: yes, 2019
This paper proposes an improved two-vector model-predictive torque control (MPTC) strategy to reduce the average torque ripple and improve the flux tracking performance.
De Belie, Frederik   +3 more
core   +1 more source

A Novel Direct Torque Control Method Based on Asymmetric Boundary Layer Sliding Mode Control for PMSM

open access: yesEnergies, 2018
A novel direct torque control (DTC) method based on sliding-mode-control (SMC) strategy is proposed for permanent magnet synchronous motor (PMSM) which is used in electric vehicles (EVs).
Qiang Song, Yiting Li, Chao Jia
doaj   +1 more source

New polymorphisms of Vkork1 gene related to anticoagulant resistance of rats and mice in Italy

open access: yesPest Management Science, Volume 81, Issue 6, Page 2869-2880, June 2025.
This study firstly reports on Vkorc1 gene mutations associated to anticoagulant rodenticide (AR) resistance in rats from Italy, and in rodents from Emilia‐Romagna region. New mutations probably involved in resistance have been described and the impact of these on rodenticide resistance was then studied via molecular docking with AR.
Alessandro Reggiani   +10 more
wiley   +1 more source

Design and Development of Low Torque Ripple Variable-Speed Drive System With Six-Phase Switched Reluctance Motors [PDF]

open access: yes, 2018
Switched reluctance motor (SRM) drives conventionally use current control techniques at low speed and voltage control techniques at high speed. However, these conventional methods usually fail to restrain the torque ripple, which is normally associated ...
Deng, Xu   +3 more
core   +2 more sources

Ibilgailu elektrikoen propultsio-sistemak: motor elektrikoak eta horien kontrola [PDF]

open access: yes, 2016
This article provides a state of the art of the electric machine technology used in Electric and Hybrid Electric Vehicle applications. Most common FOC (Field Oriented Control) and the DTC (Direct Torque Control) strategies are explained and compared ...
Arias Pujol, Antoni   +4 more
core   +2 more sources

Three level Induction Motor Torque Control Schemes for Electric Vehicles application [PDF]

open access: yes, 2014
- This work presents the results of an investigation into suitable torque control schemes for an electric vehicle application. The electric vehicle drive consists of rewound induction motors and a three-level IGBT inverter switching at 10 kHz.
Youb, Lamia
core  

Five-Axis Machine Tool Condition Monitoring Using dSPACE Real-Time System [PDF]

open access: yes, 2012
This paper presents the design, development and SIMULINK implementation of the lumped parameter model of C-axis drive from GEISS five-axis CNC machine tool.
Fletcher, Simon   +4 more
core   +1 more source

Home - About - Disclaimer - Privacy