Results 81 to 90 of about 577 (180)

Direct Torque Control of 5-Phase 10/8 Switched Reluctance Motors

Iranian Journal of Electrical and Electronic Engineering, 2009
A switched Reluctance motor (SRM) has several desirable features, including simple construction, high reliability and low cost. However, it suffers from large torque ripple, highly non-uniform torque output and magnetization characteristics and large ...
M. R. Feyzi, Y. Ebrahimi
doaj  

Control of a Wind Turbine based on DFIG by Improved Direct Torque Control using Fuzzy Logic

Revue des Énergies Renouvelables
The capacity of doubly-fed induction generators (DFIGs) to regulate both active and reactive power makes them a well-liked option for wind turbines. Direct Torque Control (DTC) is a commonly employed method for managing DFIGs, but it has limitations such
Karim Fathi Sayeh, Salah Tamalouzt, Djamel Ziane, Younes Sahri, Brahim Deffaf, Sofia Lalouni Belaid   +5 more
doaj   +1 more source

Improved DTC of Induction Motor with Fuzzy Controller [PDF]

E3S Web of Conferences
DTC, also known as Direct Torque Control, is a technique employed in variable frequency drives for regulating the torque and speed of three-phase AC electric motors. This method entails determining an approximation of the motor’s magnetic flux and torque
Manivasagam, Gupta Poonam, Singh Vaishali, Kulhar Kuldeep Singh   +3 more
doaj   +1 more source

Active Speed Compensation Method of Direct Torque Control System and Stability Analysis

Advances in Mechanical Engineering, 2015
By analyzing characteristics of the DTC (direct torque control) system in electrical driving system, a shortcoming of the classical DTC method is to point out that it is unable to decouple the mutual interference between torque and speed, so that when a ...
Rui Li, Chao-nan Tong, Xu Yang
doaj   +1 more source

Observerless Scheme for Sensorless Speed Control of PMSM Using Direct Torque Control Method With LP Filter

Advances in Electrical and Computer Engineering, 2010
In this study, direct torque control (DTC) of a permanent magnet synchronous motor is realized with a sensorless speed control technique without using an observer.
BEKIROGLU, N., OZCIRA, S.
doaj   +1 more source

Design And Implementation Of Tms320C31 Dsp And Fpga For Conventional Direct Torque Control (Dtc) Of Induction Machines

, 2009
This paper introduces a new digital logic design, which combines the DSP and FPGA to implement the conventional DTC of induction machine. The DSP will be used for floating point calculation whereas the FPGA main task is to implement the hysteresis-based controller. The emphasis is on FPGA digital logic design.
C. L. Toh, N. R. N. Idris, A. H. M. Yatim   +2 more
openaire   +2 more sources

Improving the Performance Characteristics of Three-Phase Asynchronous Induction Motor Drive Using Hybrid Systems Control Method Based on Direct Torque Control

Journal of Control Science and Engineering
In this study, a hybrid control method based on direct torque control (DTC) was introduced to enhance the performance features of the three-phase asynchronous induction motor drive.
Mohammad Shafiee-Fini, Mohammad Javad Navardi, Hossein Ghasvari   +2 more
doaj   +1 more source

A Review on DTC-SVM Method with Back-to-Back Converter Connected to the Permanent Magnet Generator and Comparison with DTC in the Matrix Converter

Majlesi Journal of Electrical Engineering
In this paper, the direct torque control torque based on space vector modulation (DTC-SVM) for permanent magnet synchronous generator connected to the variable-speed wind power generation system will be discussed.
Alireza Siadatan, Soroush Sadeghbayan, Ebrahim Afjei   +2 more
doaj  

Performance-driven switched reluctance motor drive using multiport cascaded converter and advanced direct torque control scheme. [PDF]

Sci Rep
Deepak M, Santhakumar K, Sathiyasekar K, Chokkalingam B, Padmanaban S.   +4 more
europepmc   +1 more source

FPGA Hardware in the Loop Validation of Torque and Flux Estimators for Direct Torque Control (DTC) of an Induction Motor (IM)

International Journal of Intelligent Engineering and Systems, 2021
openaire   +1 more source