Results 61 to 70 of about 12,116,196 (176)

Comparative Thermal Performance Analysis of Induction and Interior Permanent Magnet Machines for Electric Vehicles Under Varying Drive Cycles Using ANSYS Motor‐CAD Software: Approach Toward Sustainability

Engineering Reports, Volume 8, Issue 2, February 2026.
Thermal analysis of machines. ABSTRACT A comparative thermal performance study is carried out on an induction machine (IM) and an interior permanent magnet synchronous machine (i‐PMSM) for electric vehicle applications under the standardized Highway Fuel Economy Test (HWFET) and Worldwide Harmonized Light Vehicles Test Procedure (WLTP) Class 3 drive ...
R. Prasanna, S. Raja, Maher Ali Rusho, Shubham Sharma, T. Ramachandran, Krishna Prakash Arunachalam, Ghanshyam G. Tejani, Huda Fish   +7 more
wiley   +1 more source

Speed controller parameters selection in direct torque control (DTC) [PDF]

, 2005
Przedstawiono standardową strukturą układu bezpośredniego sterowania momentem (DTC) silnikiem indukcyjnym. Zaprezentowano metody doboru parametrów regulatorów prędkości P oraz PI.
Orzechowski, T., Sykulski, R., Sieklucki, G.   +2 more
core  

QUICK DYNAMIC TORQUE CONTROL IN DTC-HYSTERESIS-BASED INDUCTION MOTOR BY USING NEW OPTIMIZED SWITCHING STRATEGY [PDF]

, 2021
Induction machines are widely employed in industries due to their rugged structure, high maintainability and economy than DC motors. There has been constant development in the induction motor drive system and their implementation in industrial ...
Madhuri D. Kulkarni, Vivek D. Bavdhane
core   +2 more sources

Improving the Characteristics of the Direct FOC Strategy in DFIG‐Based Wind Turbine Systems Using FOIDD and FOPD Controllers

Energy Science &Engineering, Volume 14, Issue 2, Page 999-1021, February 2026.
This study presents a new control strategy for doubly fed induction generator (DFIG) wind turbine systems to overcome the limitations of traditional direct field control using proportional‐integral (DFOC‐PI) regulators, which are sensitive to coefficient changes and lead to low power quality.
Hamza Gasmi, Habib Benbouhenni, Z. M. S. Elbarary, Ilhami Colak, Tahar Tafticht, Salman Arafath Mohammed   +5 more
wiley   +1 more source

Performance Improvement of PMSG‐Based Wind Energy Systems via Sensorless FS‐Predictive Current Control With MRAS and MPPT‐OTC Integration

IET Electric Power Applications, Volume 20, Issue 1, January/December 2026.
This paper proposes a hybrid sensorless control strategy for a permanent magnet synchronous generator (PMSG)‐based wind energy conversion system (WECS). The approach integrates finite‐set predictive current control (FS‐PCC), a model reference adaptive system (MRAS) estimator and an optimal torque control maximum power point tracking (MPPT‐OTC) method ...
Hicham Sayhi, Amor Bourek, Abdelkarim Ammar, Ali Teta, Ahmed Chennana, Abdelaziz Rabehi, Mohamed Benghanem, Takele Ferede Agajie   +7 more
wiley   +1 more source

Improved DTC strategy of doubly fed induction motor using fuzzy logic controller

Energy Reports, 2019
This paper presents an improved Direct Torque Control (DTC) strategy for a Doubly Fed Induction Machine (DFIM) powered by two voltage source inverters (VSI) at two levels. This strategy is based on the fuzzy logic controller.
Najib El Ouanjli, Saad Motahhir, Aziz Derouich, Abdelaziz El Ghzizal, Ali Chebabhi, Mohammed Taoussi   +5 more
doaj   +1 more source

A Robust Multi‐Domain Signal Processing Framework for Early Detection of Ball Bearing Faults in Noisy and Variable Load Conditions

IET Electric Power Applications, Volume 20, Issue 1, January/December 2026.
This paper presents a hybrid signal‐processing framework for incipient bearing fault diagnosis. Discrete wavelet transform (DWT) was first used for targeted noise suppression, followed by velocity‐based envelope analysis to enhance fault‐related modulations, and wavelet packet transform (WPT) was used for precise isolation of fault‐sensitive frequency ...
Gholam Reza Agah, Akbar Rahideh, Shahin Hedayati Kia   +2 more
wiley   +1 more source

Adaptive Heuristic Direct Torque Control for High‐Phase Electronic Pole‐Changing Induction Machines: Hardware‐in‐the‐Loop and Experimental Evaluation

IET Electric Power Applications, Volume 20, Issue 1, January/December 2026.
ABSTRACT High‐phase electronic pole‐changing induction machines (ePCIMs) offer inherent redundancy and extended torque‐speed capability, making them suitable for high‐power traction applications such as electric buses and heavy‐duty electric vehicles. However, pole‐changing transitions produce severe transient currents that degrade dynamic performance ...
S. Mehdi Seyedi, Hamid A. Toliyat
wiley   +1 more source

Comparative study of direct torque control and field-oriented control for six-phase permanent magnet synchronous motor

Tạp chí Khoa học và Công nghệ
This study presents a MATLAB-based comparative simulation of a six-phase Permanent Magnet Synchronous Motor (PMSM) under field-oriented control (FOC) and direct torque control (DTC).
Thi-Anh-Em Bui, Trong Hai Nguyen, Hoang Than, Dai-Qui Vo, Quoc Thien Pham   +4 more
doaj   +1 more source

Modeling and Simulation of 12/8 poles Switched Ｒeluctance Motor Direct Torque Control System

Journal of Harbin University of Science and Technology, 2017
Aiming at the problem of the torque ripple in the development and promotion of the switched reluctance motor (SＲM)，the direct torque control (DTC) strategy is proposed in this paper for SＲM，and the realization method of DTC is presented.
ZHOU Yong-qin, XU Shuang, WU Tong, WAN Ya-zhou   +3 more
doaj   +1 more source