Results 41 to 50 of about 75,693 (241)

Influence of Experimental Parameters on the Determination of Tetragonal Distortion in Heterostructures by LACBED [PDF]

open access: yesMicroscopy Microanalysis Microstructures, 1995
The LACBED technique has been applied to the determination of the tetragonal distortion in Si 1-x Ge x /Si heterostructures, which are of great interest in the device technology. The strain determination has been performed on plan sections in an analytical electron microscope.
Armigliato A   +3 more
openaire   +2 more sources

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

open access: yesAdvanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi   +3 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera   +8 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

open access: yesAdvanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

Training sample acquisition strategy based digital pre-distortion

open access: yes, 2012
Digital pre-distortion (PD) is a promising technique for power amplifier (PA) linearization and efficiency enhancement. Parameter estimation for both PA and PD models are quite important in all pre-distortion schemes.
L Gui (13621342)   +2 more
core  

Sensitivity of Redshift Distortion Measurements to Cosmological Parameters

open access: yesThe Astrophysical Journal, 1998
The multipole moments of the power spectrum of large scale structure, observed in redshift space, are calculated for a finite sample volume including the effects of both the linear velocity field and geometry. A variance calculation is also performed including the effects of shot noise. The sensitivity with which a survey with the depth and geometry of
de Laix, Andrew A., Starkman, Glenn
openaire   +2 more sources

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Método local de correção da distorção da lente aplicado a visão estereoscópica [PDF]

open access: yes, 2014
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Engenharia Elétrica, Florianópolis, 2014.Visão estereoscópica é o processo de estimação da informação de profundidade de uma cena, ou de um ...
Pereira Junior, Osmando
core  

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi   +4 more
wiley   +1 more source

Home - About - Disclaimer - Privacy