Results 61 to 70 of about 75,693 (241)
An Image Distortion Correction Method Based on Distortion Centre and Parameter Estimation
Journal of Physics: Conference SeriesAbstract We propose a radial distortion correction method based on straight-line feature calibration to address the challenge of image radial distortion when measuring mechanical motion parameters using computer vision technology.
Wenhuang Zhao, Xing Liu, Yinhuan Zhang
openaire +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
THE IMPACT OF PROCESS PARAMETERS ON THE RESIDUAL STRESSES AND DISTORTIONS IN PULTRUSION
, 2013 In the present work, the effects of the heater configuration and pulling speed on the process induced residual stresses and distortions of a pultruded glass/epoxy flat plate have been investigated.
Baran, Ismet +2 more
openaire +2 more sources
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Transverse distortion of a relativistic composite system in impact parameter space
, 2015 We investigate the Generalized Parton Distributions (GPDs) in impact parameter space using the explicit light front wave functions (LFWFs) for the two-particle Fock state of the electron in QED.
Narinder Kumar, Harleen Dahiya
core +1 more source
Analysis of the distortion of cantilever box girder with inner flexible diaphragms using initial parameter method [PDF]
, 2017 In this paper, the distortion of cantilever box girders with inner flexible thin diaphragms is investigated under concentrated eccentric loads using initial parameter method (IPM), in which the in-plane shear strain of diaphragms is fully considered.
Wang, Y, Cheng, W, Wang, B
core +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Quantifying distortion in time-correlated single photon counting: a universal parameter
One major drawback of the classic time-correlated single photon counting (TCSPC) technique is pileup-related distortion. To keep it under a reasonable level, the maximum count rate has to be reduced, posing a serious limitation to the overall measurement
Bovolenta, Angela +3 more
core +1 more source
Wide-Angle Lens Distortion Correction Using Division Models
, 2013 In this paper we propose a new method to automatically correct wide-angle lens distortion from the distorted lines generated by the projection on the image of 3D straight lines.
Alvarez, Luis +7 more
core +1 more source