Results 131 to 140 of about 172,409 (305)

Use of dry fixative slides for exfoliative cytology [PDF]

Journal of Clinical Pathology, 1965
J, KOHN, J H, EARLE
openaire   +2 more sources

Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer

Advanced Functional Materials, EarlyView.
Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero, Meghna Jha, Elsa Veronica Flores‐Vela, Joost Kimpel, Andreas Schaefer, Jiali Guo, Jesika Asatryan, Alberto Peinador Veiga, Shuichi Haraguchi, Per‐Anders Carlsson, Jaime Martín, Mariano Campoy‐Quiles, Christian Müller   +12 more
wiley   +1 more source

Dry Sliding Wear Studies on Sillimanite and B₄C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process. [PDF]

Materials (Basel), 2022
Pethuraj M, Uthayakumar M, Rajesh S, Abdul Majid MS, Rajakarunakaran S, Niemczewska-Wójcik M.   +5 more
europepmc   +1 more source

Study on B4C Particulates Size on Mechanical Behavior, Fractured Surface and Optimization of the Wear Parameters of the Al7075 Composites by Statistical Approach

Fracture and Structural Integrity
Aluminum composites with varied weight percentages of 0-2.5 B4C particles and micro- and nanoparticle sizes were fabricated by stir-casting. The material's mechanical and wear characteristics were evaluated.
M. Ravikumar
doaj   +3 more sources

Experimental characterization of friction coefficients at the tool-chip-workpiece interface in cutting: Evaluation of lubrication efficiency of mineral oil [PDF]

, 2010
Collaboration avec le LTDS/ENISEThe characterization of friction coefficients at the tool-chip-workpiece interface remains an issue. This paper presents a new experimental set-up able to simulate similar tribological phenomena as the ones occurring at ...
CLAUDIN, Christophe, DUMONT, Florian, FROMENTIN, Guillaume, MONDELIN, Alexandre, RECH, Joël   +4 more
core   +2 more sources

Friction Coefficient of UHMWPE During Dry Reciprocating Sliding

Tribology in Industry, 2013
This paper deals with the friction coefficient behaviour during dry reciprocating sliding of UHMWPE in contact with alumina (Al2O3), within a range of velocities typical for hip implants. Five values of normal force (100 - 1000 mN) and three values of sliding speed (4 - 12 mm/s) have been observed.
Zivic, Fatima, Babic, Miroslav, Mitrovic, Slobodan, Adamovic, Dragan, Pelemis, Svetlana   +4 more
openaire   +2 more sources

Scalable Polyelectrolyte Complex‐Based Sorbent With Hourly Sorption−Desorption Cycles for Multicyclic Atmospheric Water Harvesting in Arid Environments

Advanced Functional Materials, EarlyView.
A polyelectrolyte complex‐based sorbent is produced by scalable, environmentally benign aqueous phase inversion. Its porous, LiCl‐ and GO‐integrated architecture enables hourly adsorption−desorption cycles at low relative humidity (RH < 30%). A large‐scale prototype achieves multicyclic, solar‐driven atmospheric water harvesting of 1.37 L kg−1 day−1 ...
Seung‐Hwan Oh, Incheol Heo, Won Cheol Yoo, Soo‐Hyung Choi   +3 more
wiley   +1 more source

Dry Sliding Wear and Corrosion Performance of Mg-Sn-Ti Alloys Produced by Casting and Extrusion. [PDF]

Materials (Basel), 2022
Bovand D, Abdollah-Pour H, Mirzaee O, Bagherifard S.   +3 more
europepmc   +1 more source

Polymeric Composites: Failures in Dry Sliding on Steel

Tribology in Industry
The investigation of a tribosystem failure is important in establishing its causes with the highest probability. This paper proposes a discussion on particular aspects of failure in polymeric composites sliding against steel in dry regime. At micro level, failure mechanisms of polymeric composites in dry sliding on steel could explain damages or ...
Lorena Deleanu, Alina Cantaragiu Ceoromila, Constantin Georgescu, Mihail Botan, George Ghiocel Ojoc, Ioana Gabriela Chiracu   +5 more
openaire   +2 more sources

High‐Resolution and Real‐Time In Situ Generation of Cellular Spheroids by Laser‐Assisted Bioprinting for Guided Microvascularization

Advanced Functional Materials, EarlyView.
Micro‐injection laser‐assisted bioprinting enables ultrafast and precise patterning of small endothelial cell spheroids by injecting a highly concentrated single‐cell suspension into GelMA/ColMA hydrogels. In co‐culture with fibroblasts, controlled pre‐vasculogenic network formation is obtained at microscale resolution.
Charles Handschin, Katharina Wulz, Clotilde Jugie, Marie‐Laure Stachowicz, Shane Fennell, Aurélien Mazet, Malou Lea, Nathalie Dusserre, Jean‐Christophe Fricain, Hugo Oliveira   +9 more
wiley   +1 more source