Results 201 to 210 of about 560,359 (310)

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Study on the effect of moisture content on the spectral detection of soluble solids in apricot. [PDF]

Sci Rep
Kang L, Luo H, Ma X, Yu J, Liu H, Liu H, Tong Y.   +6 more
europepmc   +1 more source

Tape as a means to ensure air- and watertightness of building joints : experimental assessment [PDF]

, 2017
Maroy, Katrien, Steeman, Marijke, Van Den Bossche, Nathan, Van Linden, Stéphanie   +3 more
core  

Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter, Felix Drechsler, Till M. J. Stadtmüller, Cameliu Himcinschi, Christos G. Aneziris, Jens Kortus   +5 more
wiley   +1 more source

Environmental and energetic exergetic sustainability of stevia leaf drying in a PVT indirect solar dryer with variable airflow and tray levels. [PDF]

Sci Rep
Elwakeel AE, Oraiath AAT, Tantawy A, Székács A, Saeed O, Eid MH, Mahmoud SF, Aljumayi H, AlQthanin RN, Abdallah SE, Yousif IAH, Tantawy AA.   +11 more
europepmc   +1 more source

Care solution effects on contact lens in vivo wettability [PDF]

, 2017
Abusharha, Ali A., Fagehi, Raied, Oliver, Katherine, Pearce, E. Ian, Tomlinson, Alan   +4 more
core   +2 more sources

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Water recovery of drying waste using a thermoelectric cooler and PV/T assisted. [PDF]

Sci Rep
Elbrashy A, El-Fakharany MK, Al-Sood MA, Abou-Taleb FS, Essa FA.   +4 more
europepmc   +1 more source

42. Finishing performance of pigs fed dry feed vs. wet/dry feed

Animal - science proceedings, 2021
openaire   +1 more source

Drying behaviour of calcium silicate [PDF]

, 2014
De Paepe, Michel, Janssens, Arnold, Steeman, Marijke, Van Belleghem, Marnix   +3 more
core   +1 more source