Results 41 to 50 of about 8,617 (305)
Archives of Metallurgy and Materials, 2016 The article presents a statistical analysis of data collected from the observation of the production of austempered ductile iron. The impact assessment of the chemical composition, i.e.
Nawrocki P., Kochański A., Myszka D.
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
A Study on Wear and Erosion-Corrosion Resistance of Two Typs of Cast Irons. [PDF]
Engineering and Technology Journal, 2008 The wear and erosion-corrosion resistance of gray and ductile cast ironswere studied for their important in most applications. The wear tests were carriedout using a pin-on-disc machine by applying different loads (10,20 and 30 N).
Sami A.Ajeel, Safaa Mohammed Hasoni
doaj +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Research and Analysis of the Effect of Heat Treatment on Damping Properties of Ductile Iron
Open Physics, 2019 With the continuous development of metal manufacturing technology, high-strength and high-hardness ductile iron materials have excellent comprehensive performance.
Zhang Yu +5 more
doaj +1 more source
Thermo-mechanical behaviour of spheroidal graphite iron in the austenitic phase [PDF]
, 2013 The main objective of this paper is to identify the thermo-mechanical behaviour at high temperature of the spheroidal graphite (SG) iron EN-GJS-700-2. In the rst instance, tensile and compression tests in austenitic phase are performed.
LE MERCIER, Kévin +4 more
core
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Estudo da soldagem de recuperação do ferro fundido vermicular através do processo oxiacetilênico [PDF]
, 2005 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Ciência e Engenharia de Materiais.Este trabalho tem por objetivo avaliar o comportamento do ferro fundido vermicular frente ao processo de
Canale, Anderson Junior
core
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
npj Materials DegradationThis study deciphers the chloride-induced early-stage corrosion of Cr/RE-microalloyed HRB400 rebars in saturated Ca(OH)₂ pore solutions (0.5–3.5 wt% Cl⁻).
Renzheng Zhu +8 more
doaj +1 more source