Results 11 to 20 of about 4,566,403 (297)

General dynamic recovery for compensating CSP [PDF]

open access: yesElectronic Proceedings in Theoretical Computer Science, 2014
Compensation is a technique to roll-back a system to a consistent state in case of failure. Recovery mechanisms for compensating calculi specify the order of execution of compensation sequences.
Abeer S. Al-Humaimeedy   +1 more
doaj   +4 more sources

Moisture Recovery – A Dynamic Modelling Approach [PDF]

open access: yesE3S Web of Conferences, 2019
With rising insulation standards, the use of mechanical ventilation, especially in non-residential buildings, is becoming increasingly relevant. To ensure thermal comfort and avoid health problems for people in the room, cost- and energy-intensive ...
Kremer Martin, Mathis Paul, Müller Dirk
doaj   +3 more sources

Recovery ... reporting overview; Connecticut recovery; CT recovery ... progress

open access: yes, 2010
Updated quarterly; Began in 2009.; Title from home page last modified 10/29/2009 (viewed Oct. 29, 2009).; At head of title: State of Connecticut.; "On October 1, state agencies that have received Recovery Act funds began reporting to the federal ...

core   +5 more sources

Nonstationary Bandits with Habituation and Recovery Dynamics [PDF]

open access: yesOperations Research, 2020
In many sequential decision-making settings where there is uncertainty about the reward of each action, frequent selection of specific actions may reduce expected reward while choosing less frequently selected actions could lead to an increase. These effects are commonly observed in settings ranging from personalized healthcare interventions and ...
Yonatan Mintz   +4 more
openaire   +3 more sources

Failure and recovery in dynamical networks [PDF]

open access: yesScientific Reports, 2017
AbstractFailure, damage spread and recovery crucially underlie many spatially embedded networked systems ranging from transportation structures to the human body. Here we study the interplay between spontaneous damage, induced failure and recovery in both embedded and non-embedded networks.
L. Böttcher   +4 more
openaire   +4 more sources

Growth Dynamics: The Myth of Economic Recovery [PDF]

open access: yesAmerican Economic Review, 2005
Using panel data for a large set of high-income, emerging market, developing, and transition countries, we find robust evidence that the large output loss from financial crises and some types of political crises is highly persistent. The results on financial crises are also highly robust to the assumption on exogeneity.
Valerie Cerra, Sweta Chaman Saxena
openaire   +5 more sources

Some aspects of microstructure and properties of Al-Mg alloys after shear spinning and cold rolling [PDF]

open access: yesHemijska Industrija, 2013
Three commercial Al-Mg alloys containing 3 wt.% to 6 wt.% of Mg (AlMg3, AlMg4.5Mn and AlMg6Mn) were subjected to different forming processes: shear spinning and cold rolling.
Radović Ljubica M.   +2 more
doaj   +1 more source

Microstructure Evolution Behavior of Spray-Deposited 7055 Aluminum Alloy during Hot Deformation

open access: yesMetals, 2022
The evolution behaviors of the second phase, substructure and grain of the spray-deposited 7055 aluminum alloy during hot compression at 300~470 °C were studied by scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and ...
Di Feng   +8 more
doaj   +1 more source

Flow Behavior and Microstructure of Hot-Worked Fe-30.9Mn-4.9Al-4.5Cr-0.4C and Fe-21.3Mn-7.6Al-4.3Cr-1C Low-Density Stainless Steels

open access: yesApplied Sciences, 2023
Two as-cast low-density steels grades (austenite-based duplex Fe-30.9Mn-4.9Al-4.5Cr-0.4C and austenitic Fe-21.3Mn-7.6Al-4.3Cr-1C) with an initial dendritic microstructure were subjected to hot working conditions to understand the influence of deformation
Takatso Komane   +4 more
doaj   +1 more source

Novel Approach to Grain Boundary Modification in Stainless and Duplex Steel L-PBF Components through In Situ Heat Treatment

open access: yesCrystals, 2023
Additive manufacturing (AM) has provided new possibilities for improving the grain boundary properties of metallic components. However, effectively modifying the microstructure, particularly the grain boundary properties, of laser powder bed fusion (L ...
Mohsen Taheri Andani   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy