Results 21 to 30 of about 8,677 (268)

Research on Casting Process of Electrolytic Aluminum Anode Phosphorus Cast Iron and Carbon Block based on ProCAST [PDF]

Archives of Foundry Engineering
In order to obtain a better connection state between the carbon block and steel claw of aluminum guide rod in the electrolytic aluminum anode assembly, the casting simulation software (ProCAST) was used to simulate the casting process of phosphorus cast ...
Kun Zhang, Rong Li
doaj   +1 more source

Development of a EBSD-FEM data conversion interface and the image-based crystal plasticity analysis

Nihon Kikai Gakkai ronbunshu, 2018
Image-based deformation simulation of microstructures in metals is attracting attention; however, the data conversion processes from the images of microstructures into the geometric models for the deformation simulation are now inconvenient, and there is
Yoshiki KAWANO, Tetsuya OHASHI, Tsuyoshi MAYAMA, Masaki TANAKA, Morihiro SAKAMOTO, Yelm OKUYAMA, Michihiro SATO   +6 more
doaj   +1 more source

Examination of Formability Properties of 6063 Alloy Extruded Profiles for the Automotive Industry

Metals, 2019
Bendability is a crucial property of automotive parts, which describes the ability of extruded profiles to be formed to shape, without the appearance of discontinuities that will have an adverse effect on the mechanical properties and their energy ...
Athanasios Vazdirvanidis, Ioannis Pressas, Sofia Papadopoulou, Anagnostis Toulfatzis, Andreas Rikos, Marianna Katsivarda, Grigoris Symeonidis, George Pantazopoulos   +7 more
doaj   +1 more source

Effect of crystallographic properties on low cycle fatigue crack initiation at elevated temperature for Ni-based directionally solidified superalloy

Nihon Kikai Gakkai ronbunshu, 2016
Low cycle fatigue tests at elevated temperature were conducted on a Ni-based directionally solidified superalloy subjected to transverse loading. To investigate the effect of the arrangement and the orientation of crystal grains on the crack initiation ...
Takashi YOKOYAMA, Masaru SEKIHARA
doaj   +1 more source

Aplicación de técnicas de nanoindentación y EBSD en aceros con microestructuras complejas

Revista de Metalurgia, 2008
En el presente trabajo, se ha estudiado el comportamiento mecánico de aceros con microestructuras ferrito-perlíticas y ferrito-martensíticas y la relación de estas con la microestructura.
M. A. Altuna, I. Gutiérrez
doaj   +1 more source

Evolution of Microstructure, Texture and Topography during Cold Rolling and Recrystallization of Ni–5at.%W Alloy Substrate for Coated Conductors

Crystals, 2019
In this work, the effect of cold rolling and heat treatment upon the microstructure and texture of the surface layer and cross-section of Ni5W alloy substrate was analyzed via the EBSD technique. A typical copper deformation texture was shown by the cold-
Chenxi Zhang, Hongli Suo, Zili Zhang, Qiuliang Wang, Yingxia Wang, Lin Ma, Min Liu, Yaotang Ji, Jiazhi Li   +8 more
doaj   +1 more source

Development of damage evaluation system for heat resistant steel for creep and creep fatigue based on deep learning of grain shape and strain information by EBSD observation

Cogent Engineering, 2021
EBSD observations were conducted on the damaged materials obtained by interrupted creep tests and interrupted creep-fatigue tests for 304 austenitic stainless steel for boiler tube use in fossil power plants, and the shapes of crystal grains extracted ...
Yu Kurashige, Sho Takami, Kazunari Fujiyama   +2 more
doaj   +1 more source

Problemas en la reparación por laser cladding de superficies de acero AISI D2 tratado térmicamente

Revista de Metalurgia, 2010
Se ha depositado polvo de acero de herramienta (H13) sobre diferentes sustratos de acero que se encuentran en estado metalúrgico diferente (recocido o de temple y revenido) para comparar los resultados y se ha analizado la microestructura del ...
J. J. Candel, V. Amigó, J. A. Ramos, D. Busquets   +3 more
doaj   +1 more source

Evaluation of fatigue damage in a pure copper with nonlinear three-wave interaction

Nihon Kikai Gakkai ronbunshu, 2016
We investigated nonlinear ultrasonic characterization, nonlinear three-wave interaction, of the pure copper during fatigue with EMAR (Electromagnetic Acoustic Resonance), which was the combination with ultrasonic resonance and non-contacting transducer ...
Yutaka ISHII, Toshihiro OHTANI, Masayoshi NAKANIWA, Masayuki KAMAYA   +3 more
doaj   +1 more source

Effects of the Growth Rate on the High-temperature Tensile Properties and Micro-organization of Directionally Solidified Ti-44Al-9Nb-1Cr-0.2W-0.2Y Alloys

Medžiagotyra, 2023
In this experiment, Ti-44Al-9Nb-1Cr-0.2W-0.2Y alloy was prepared by the directional solidification method. The effect of different growth rates on tensile properties and microstructure orientation at high temperature was studied.
Yao HUANG, Zhuhang JIANG, Renheng HAN, Chengzhi ZHAO, Hexin ZHANG   +4 more
doaj   +1 more source