Results 141 to 150 of about 1,647,342 (298)
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Results of basic improvements to the extraction of spectra from IUE images [PDF]
Results of two methods of extracting spectra from IUE images are compared. The first method, which is presently implemented, performs a geometric correction of the image followed by a photometric correction.
Bohlin, R. C., Lindler, D. J.
core +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source