Results 71 to 80 of about 17,706 (234)

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Effect of Buckling Restrained Braces Locations on Seismic Responses of High-Rise RC Core Wall Buildings

Shock and Vibration, 2016
Conventionally, a flexural plastic hinge is designed and detailed at the core wall base and coupling beams ends to control the seismic responses. This strategy is based on allowing the damage to be concentrated on main structural components.
Munir Ahmed, Shahzadi Tayyaba, Muhammad Waseem Ashraf   +2 more
doaj   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Investigation into the Fracture Evolution Law of Overlying Strata Roof in Shallowly Buried “Three-Soft” Coal Seam Fully Mechanized Mining Faces and Its Influence on the Feasibility of Gob-Side Entry Retaining

Applied Sciences
To address the feasibility of gob-side entry retaining in the shallow-buried three-soft coal seam fully mechanized mining face (SB-TSCS FMMF) of Xindeng (Zhengzhou, China) Coal Industry, we established a mechanical model of post-mining roof–coal-rock ...
Guoyou Hu, Yongkang Yang, Shuai Li, Konghao Zhu   +3 more
doaj   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials

Advanced Engineering Materials, EarlyView.
This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline, Matthew Santer, Robert Hewson   +2 more
wiley   +1 more source

Tekuk Torsi Lateral Balok I Kantilever Non Prismatis

Jurnal Teknik Sipil, 2014
Abstrak. Dalam makalah ini disajikan hasil dari suatu studi tentang tekuk torsi lateral elastis balok kantilever dengan penampang I nonprismatis. Bentuk ketidak prismatisan adalah ketinggian badan (web) bervariasi linier sedangkan lebar sayap konstan ...
Paulus Karta Wijaya, Paulina Jacintha
doaj  

Lateral Torsional Buckling of Steel Beams Elastically Restrained at the Support Nodes

Applied Sciences, 2019
The study shows the results of theoretical investigations into lateral torsional buckling of bisymmetric I-beams elastically restrained against warping and against rotation in the plane of lateral torsional buckling (i.e., against lateral rotation) at ...
Rafał Piotrowski, Andrzej Szychowski
doaj   +1 more source

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source