Results 71 to 80 of about 846,677 (301)
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Transistor step stress program for JANTX2N2432A [PDF]
Power/temperature step stress was applied to the transistor JANTX2N2432A manufactured by Crystalonics and Texas Instruments. A total of 48 samples from each manufacturer were submitted to the process outlined.
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
The Use of Piezoelectric Actuators in an Energy-Efficient Noise Reduction System [PDF]
, 2015 The piezoelectric effect allows for conversion between mechanical stress and electrical impulses. By utilizing this phenomenon, a novel method of sound attenuation was explored and tested in which a piezoelectric plate absorbs part of an incoming sound ...
Johnson, Ian J.M.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Modelling a Coupled Thermoelectromechanical Behaviour of Contact Elements via Fractal Surfaces [PDF]
, 2016 A three-dimensional coupled thermoelectromechanical model for electrical connectors is here proposed to evaluate local stress and temperature distributions around the contact area of electric connectors under different applied loads.
GUARNIERI, MASSIMO +2 more
core +3 more sources
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Pressure stimulated currents in rocks and their correlation with mechanical properties [PDF]
, 2004 The spontaneous electrification of marble samples was studied while they were subjected to uniaxial stress. The Pressure Stimulated Current (PSC) technique was applied to measure the charge released from compressed Dionysos marble samples, while they ...
Agioutantis, Z +6 more
core +3 more sources
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Transistor step stress program for JANTX2N2060 [PDF]
The effect of power/temperature step stress when applied to the dual transistor JANTX2N2060 manufactured by Raytheon and Motorola is reported. A total of 48 samples from each manufacturer were submitted to the process.
core +1 more source