Results 101 to 110 of about 1,274,784 (313)

Practical Characterization of Cell-Electrode Electrical Models in Bio-Impedance Assays [PDF]

open access: yes, 2018
This paper presents the fitting process followed to adjust the parameters of the electrical model associated to a cell-electrode system in Electrical Cell-substrate Impedance Spectroscopy (ECIS) technique, to the experimental results from cell-culture ...
Daza Navarro, María Paula   +7 more
core   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin   +5 more
wiley   +1 more source

Disposable Injection Molded Conductive Electrodes Modified with Antimony Film for the Electrochemical Determination of Trace Pb(II) and Cd(II)

open access: yesSensors, 2019
This work describes a novel electrochemical sensor fabricated by an injection molding process. This device features a conductive polymer electrode encased in a plastic holder and electroplated in situ with a thin antimony film.
Savvina Christidi   +6 more
doaj   +1 more source

Metal chloride cathode for a battery [PDF]

open access: yes, 1991
A method of fabricating a rechargeable battery is disclosed which includes a positive electrode which contains a chloride of a selected metal when the electrode is in its active state.
Bankston, C. Perry   +2 more
core   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

open access: yesAdvanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk   +7 more
wiley   +1 more source

Additive for zinc electrodes [PDF]

open access: yes, 1983
A zinc electrode for alkaline cells includes up to about ten percent by weight of Ba(OH)2.8H2O with about five percent being preferred.
Nagle, W. J.   +2 more
core   +1 more source

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler   +9 more
wiley   +1 more source

EXPERIMENT ON CREATION OF OPTIMAL AIR PROTECTION SYSTEMS IN ELECTRODEPOSITION

open access: yesAdvanced Engineering Research, 2010
Research results of the regime parameters of the process installation and application experience of the combined security facilities of the operating space from harmful electrolyte emissions in agricultural engineering are offered.
Vladimir L. GAPONOV, Vladimir I. GARSHIN
doaj  

Scanning Gate Spectroscopy on Nanoclusters

open access: yes, 1999
A gated probe for scanning tunnelling microscopy (STM) has been developed. The probe extends normal STM operations by means of an additional electrode fabricated next to the tunnelling tip.
Canali, L.   +2 more
core   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

open access: yesAdvanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy