Results 111 to 120 of about 1,274,784 (313)
Study of using three dimensional printer for EDM electrode fabrication [PDF]
, 2011 In this study, Cu-Al2O3 powder was prepared using ball mill and used separately for powder metallurgy (PM) and Three Dimensional Printer (3DP) application to fabricate electrode for electrical discharge machining (EDM).
Hassan, Noor Haslyena
core
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
An investigation of planar array system artefacts generated within an electrical impedance mammography system developed for breast cancer detection [PDF]
, 2014 An Electrical Impedance Mammography (EIM) planar array imaging system is being developed at the University of Sussex for the detection of breast cancers.
Bilal, Rabia +3 more
core
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang +3 more
wiley +1 more source
A STUDY ON pH ANALYZER USING ARTIFICIAL INTELLIGENCE IN WATER MANAGEMENT OF THERMAL POWER GENERATION PLANT [PDF]
European Journal of Materials Science and Engineering, 2018 pH is a very important factor that critically affects the efficiency of desulfurization facilities as well as in the generation of boiler tube scales in power plants as an indicator of hydrogen ion concentration of the aqueous solution.
Juhyeong KIL
doaj
Deterministic Detection of Single Ion Implantation
Advanced Engineering Materials, EarlyView.Focused ion beam implantation with high detection efficiencies will enable the rapid and scalable fabrication of advanced spin‐based technologies such as qubits. This work presents the detection efficiencies of a wide range of ions implanted into solid‐state hosts, with efficiencies of >90% recorded for ion species and substrate combinations of ...
Mason Adshead +6 more
wiley +1 more source
Mass Erosion and Material Transfer at the Deposition of Layers by Inverse Electroerosion
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2008 The deposition and alloying of the superficial layers by inverse electroerosion or by electric spark given by a vibrating electrode permits to obtain a large scale of properties at the surface of metallic materials from tools, machines organs, electric ...
Adrian ALEXANDRU +2 more
doaj
Advanced Engineering Materials, EarlyView.This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay +3 more
wiley +1 more source
Analytical and experimental studies of thermionically emitting electrodes in contact with dense, seeded plasmas [PDF]
, 1970 Interactions are considered between a moving, alkali-metal seeded, dense plasma and a metallic electrode whose surface properties are influenced by the absorption of seed particles. The plasma behavior is governed by a set of differential equations,
Koester, John K. +2 more
core