Results 151 to 160 of about 4,278,026 (378)

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

The Electron Microscope in Palaeopathology [PDF]

Medical History, 1969
R. F. Macadam, A. T. Sandison
openaire   +3 more sources

An Electron Microscope Study of the Nuclear Membrane [PDF]

, 1949
H. G. Callan, J. T. Randall, S G Tomlin
openalex   +1 more source

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

An X-ray and electron microscope study of tropomyosin [PDF]

, 1948
W. T. ASTBURY, R. Reed, L. C. Spark
openalex   +1 more source

Investigation of Oxide Dispersion Strengthening Effect on the Strength of Diffusion‐Bonded AISI304 Parts

Advanced Engineering Materials, EarlyView.
Experiments for reinforcing the diffusion bonding plane by the oxide dispersion strengthening effect are presented. Small ceramic particles (0.5 and 50 μm, respectively) are incorporated. Furthermore, ceramic particles help to penetrate stable passivation layers, enabling atomic diffusion across bonding planes. Since a ceramic–metallic interface cannot
Thomas Gietzelt, Mario Walter, Volker Toth, Florian Messerschmidt, Melina Blem   +4 more
wiley   +1 more source

Toughness of Confined Auxetic Foams

Advanced Engineering Materials, EarlyView.
Auxetic (negative Poisson's ratio) materials offer benefits such as impact mitigation, thermal insulation, vibration damping, and reduced shear strain, although their fracture mechanics are largely unexplored. This study investigates damage initiation and propagation in confined re‐entrant auxetic foams from polyurethane via experimental ...
Adrianos E. F. Athanasiadis, Oliver Duncan, Michal K. Budzik, Marcelo A. Dias   +3 more
wiley   +1 more source

On the Deformation Behavior of Metastable CrMnNi Steels Processed by Directed Energy Deposition in Different Temperature Regimes

Advanced Engineering Materials, EarlyView.
In the present study, metastable CrMnNi steels with varying chemical compositions and a concomitantly altered stacking fault energy are processed via directed energy deposition and afterwards tested via tensile tests at different temperatures. The present study shows the influence of the manufacturing process on the elemental deformation mechanisms for
Julia Richter, Thomas Wegener, Florian Stredak, Gert Bartzsch, Steffen Scherbring, Javad Mola, Olena Volkova, Stefan Böhm, Thomas Niendorf   +8 more
wiley   +1 more source

Direct Electron Detection Electron Energy‐Loss Spectroscopy: Speeding Up 2D Analytical In Situ Transmission Electron Microscopy for Aluminum Alloys

Advanced Engineering Materials, EarlyView.
Scanning transmission electron microscopy imaging techniques are an essential tool to document dynamic developments, such as precipitation in aluminum alloys, during in situ heating experiments using transmission electron microscopy. However, in many cases, chemical information is required to interpret complex nanoscale processes.
Evelin Fisslthaler, Martina Dienstleder, Judith Lammer, Moritz Theissing, Daniel Knez   +4 more
wiley   +1 more source

Study of the Effect of Process Parameters and Heat Treatment on the Formation and Evolution of Directed Energy Deposition of IN718‐CuCrZr Interface

Advanced Engineering Materials, EarlyView.
Bimetallic structures of Inconel 718 and CuCrZr are fabricated using the laser powder directed energy deposition method. The study reveals a strong dependence of interface characteristics such as width and interfusion on processing and heat treatment strategies.
Hamidreza Javidrad, Bahattin Koc
wiley   +1 more source