Results 21 to 30 of about 5,423 (220)
Microstructure of severely deformed metals from X-ray line profile analysis [PDF]
, 2006 Two essentially different materials, cubic Ti(49.8)Ni(50.2) shape memory alloy and hexagonal AZ91 Mg alloy, were deformed by equal channel angular pressing (ECAP).
Gubicza, Jenő +3 more
core +1 more source
Zjemňování zrna protlačované hořčíkové slitiny AZ31 procesem Ecap [PDF]
, 2017 Extruded Mg – 3%Al – 1% Zn (AZ31) magnesium alloy was subjected to ECAP (Equal Channel Angular Pressing) processing at 523 K (250 °C). At the processing temperature of 523 K, fine grains with the average grain size of 2 – 3 μm are formed as a result of ...
Hilšer, Ondřej +3 more
core +1 more source
Journal of Magnesium and Alloys, 2020 Two step equal channel angular pressing carried out on as cast ZE41 Mg alloy resulted in a remarkable grain refinement. As compared to grain size of 46 µm in as cast sample, refinement upto 2.5 µm was achieved after 8th pass equal channel angular ...
S. Prithivirajan +2 more
doaj +1 more source
Journal of Materials Research and Technology, 2017 Oxygen-free copper of 99.95Â wt.% purity was severely deformed at room temperature by two modes of severe plastic deformation, equal-channel angular pressing (ECAP) and high-pressure torsion (HPT).
Meshal Y. Alawadhi +3 more
doaj +1 more source
Experimental study on severe plastic deformation of Ti by novel equal-channel angular pressing [PDF]
, 2012 This study involves experimental investigation on severe plastic deformation (SPD) of Ti using novel equal-channel angular pressing (ECAP) at ambient temperature.
Fujiwara, Eri Miura +3 more
core +1 more source
Journal of Magnesium and Alloys, 2017 As-extruded Mg-6Zn (wt.%) Alloy was subjected to severe plastic deformation (SPD) by the equal-channel angular pressing(ECAP) at 160 oC. The results of tensile tests at room temperature showed that two passes ECAP resulted in a remarkable improvement of ...
Kai Yan +3 more
doaj +1 more source
ECAP process improvement based on the design of rational inclined punch shapes for the acute-angled Segal 2θ-dies: CFD 2-D description of dead zone reduction [PDF]
Mechanical Sciences, 2015 This article is focused on a 2-D fluid dynamics description of punch shape geometry improvement for Equal Channel Angular Extrusion (ECAE) or Equal Channel Angular Pressing (ECAP) of viscous incompressible continuum through acute-angled Segal 2θ-dies ...
A. V. Perig, N. N. Golodenko
doaj +1 more source
Optimization Process Parameters of Equal Angular Channel Pressing According to the Measurement Results of Microstructural Homogeneity [PDF]
Materials Research, 2018 The aim of the present work is to discuss process parameters effect on microstructure evolution and formation mechanism of ultrafine grains. As plastic deformation technique Equal Channel Angular Pressing (ECAP) method used pure Ti G4 rods processed in ...
Asli Günay Bulutsuz +2 more
doaj +1 more source
Ultrafine grains - a new option for light metals [PDF]
, 2009 The potential of ultrafine grained light metals is reviewed. The fundamental metallurgical processes, microstructures developed and properties obtained are first considered.
Olejnik, L., Rosochowski, A.
core +1 more source
International Islamic University Malaysia Engineering Journal, 2010 The die geometry has a massive effect on the plastic deformation behavior during pressing of material processed by equal channel angular pressing (ECAP) method; subsequently the properties of the processed material are strongly dependent on it.
Ali A Aljubouri
doaj +1 more source