Results 161 to 170 of about 2,214,130 (267)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

A finite element study on three maxillary protraction devices for treating maxillary sagittal hypoplasia at different levels of bone fusion. [PDF]

Front Bioeng Biotechnol
Sun K, Zhao G, Jin Y, Tang B, Liu Y, Wang L.   +5 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Single-Switch Inverter Modular Parallel Multi-Voltage Levels Wireless Charging System for Robots. [PDF]

Sensors (Basel)
Li H, Sun Z, Wei L.
europepmc   +1 more source

Numerical Investigation of a Dual‐Mode Shape Memory Alloy Stent Enabling Secondary Expansion via Focused Ultrasound: A Potential Strategy for Correcting In‐Stent Restenosis

Advanced Engineering Materials, EarlyView.
This study demonstrates a novel noninvasive strategy to treat in‐stent restenosis using focused ultrasound. A shape memory alloy stent initially expands at body temperature. If restenosis occurs, targeted ultrasound heating thermally actuates the stent, enabling a secondary expansion to reopen the blocked vessel, offering a potential alternative to ...
Stephen Asare, Lucinda Duncan, Josiah Owusu‐Danquah, Brian L. Davis   +3 more
wiley   +1 more source

Distribution of static and dynamic cyclotorsion and influencing factors in FS-LASIK. [PDF]

Front Med (Lausanne)
Ning J, Mu Y, Sun S, Yu T, Liu X, Zhang Q, Zhang L.   +6 more
europepmc   +1 more source

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Calculation Simulation of Equivalent Thermomechanical Properties of Dispersion Nuclear Fuel. [PDF]

Materials (Basel)
Yu H, Cong T, Zhang J.
europepmc   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Optimization of Mechanical Properties of Multiphase Materials with Auxetic Phase. [PDF]

Materials (Basel)
Zawistowski M, Poteralski A.
europepmc   +1 more source