Results 41 to 50 of about 66,628 (356)
A Review of the Erosion of Thermal Barrier Coatings. [PDF]
, 2007 The application of thermal barrier coatings (TBCs) to components with internal cooling in the hot gas stream of gas turbine engines has facilitated a steep increase in the turbine entry temperature and the associated increase in performance and ...
Nicholls, John R., Wellman, R. G.
core +1 more source
Studying and comparing the erosion-enhanced pitting corrosion of X52 and X100 steels
International Journal of Electrochemical Science, 2012 The critical ratio of Cl− to HCO− concerning the corrosion rate has been determined with and without electrolyte erosion in 0.3 M NaHCO3 by using various concentrations of NaCl for X52 and X100 steels.
A. Rauf, E. Mahdi
doaj +1 more source
Low impact velocity wastage in FBCs : experimental results and comparison between abrasion and erosion theories [PDF]
, 2012 The use of technologies related to combustion of coal in fluidized bed combustors (FBCs) present attractive advantages over conventional pulverized coal units.
Almeraya-Calderón, F. +3 more
core +2 more sources
Study of Erosion- Corrosion Behavior of Aluminum Metal Matrix Composite [PDF]
Engineering and Technology Journal, 2014 The aim of present work is to study the erosion –corrosion behavior of aluminum metal composite which consists of the (Al – 12wt % Si) alloy as matrix phase and 10wt% SiC particles as reinforcing phase.
Muna K. Abbass +1 more
doaj +1 more source
Augmentation of the mechanical and chemical resistance characteristics of an Al2O3-based refractory by means of high power diode laser surface treatment [PDF]
, 2003 Augmentation of the wear rate and wear life characteristics of an Al2O3-based refractory within both normal and corrosive (NaOH and HNO3) environmental conditions was effected by means of high power diode laser (HPDL) surface treatment.
Borodina +19 more
core +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Erosion - Corrosion of Cermet Coating
International Journal of Electrochemical Science, 2013 Cermet-based coatings are being increasingly used to combat erosion-corrosion in oil and gas industries such that occurring in offshore piping, production systems and machinery involving fluid and/or slurry flowing corrosive media which often contain ...
Magdy M. El Rayes +2 more
doaj +1 more source
Crystals, 2021 Two kinds of Ti-alloys, i.e., Al–5Ti and Al–10Ti alloys, were manufactured in this study, and their ultrasonic cavitation erosion behaviors in 3.5 wt.% NaCl solution were evaluated by the cumulative mass loss, scanning electronic micrograph, and three ...
Jingtao Zhao +3 more
doaj +1 more source
, 1978 The deterioration of materials by corrosion or erosion by itself presents a formidable problem and for this reason investigators have studied these two phenomena independently. In fact, there are very few systematic studies on E-C and the majority of references mention it only in passing.
openaire +2 more sources
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source