Results 71 to 80 of about 66,628 (356)
Microstructures and erosion-corrosion behavior of Fe-B alloy containing chromium and nickel [PDF]
China Foundry, 2019 The Fe-B alloy containing chromium and nickel was prepared, and the microstructure and erosion-corrosion behavior of the alloy were investigated by means of scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction analysis ...
Da-wei Yi, Yu-pu Shi, Han-guang Fu
doaj +1 more source
Erosion-corrosion behaviour of Zirconia WC-6Co, WC-6Ni and SS316 [PDF]
, 2015 The current study investigates a ceramic, two cermets and a metal under solid-liquid impingement with 3.5% NaCl and 150mg/l hydraulic fracturing sand at two extreme angles of impact, 90° and 20°.
Andrews, N. +3 more
core
Self-stabilised fractality of sea-coasts through damped erosion [PDF]
, 2003 Erosion of rocky coasts spontaneously creates irregular seashores. But the geometrical irregularity, in turn, damps the sea-waves, decreasing the average wave amplitude.
A. Baldassarri +14 more
core +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Erosion–Corrosion of AISI 304L Stainless Steel Affected by Industrial Copper Tailings
Metals, 2020 A comprehensive analysis of the erosion–corrosion behavior of AISI 304L stainless steel immersed in 0.5 M NaCl solution with the addition of industrial tailing particles obtained from the copper mining industry is reported. From fundamental studies using
Álvaro Soliz +3 more
doaj +1 more source
A contrastive characterization of pure Mg and AZ91D alloy based on the testing of mechanical, corrosion, wear, and erosion properties [PDF]
, 2023 Sivasankara Raju Rallabandi +6 more
openalex +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
The effect of fluid velocity and microstructure on erosion corrosion of two-phase CK45 steel
Results in Materials, 2020 The essential factor to reduce the overall cost in many industries which facing erosion-corrosion phenomenon is the choice of correct design and material selection.
Sajjad akramian Zadeh, Pourya Rashidi
doaj +1 more source
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Erosion-corrosion of Cr3C2-Ni cermets in salt water [PDF]
, 2006 Chromium carbide based cermets are popular materials in different industrial applications due to their unique properties. These materials have outstanding erosion resistance up to 1000 °C and excellent oxidation resistance up to 850 °C.
Antonov, Maksim +2 more
core