Results 91 to 100 of about 115,445 (306)
Thermoresponsive poly(2-oxazoline)s, polypeptoids, and polypeptides [PDF]
, 2017 This review covers the recent advances in the emerging field of thermoresponsive polyamides or polymeric amides, i.e., poly(2-oxazoline)s, polypeptoids, and polypeptides, with a specific focus on structure-thermoresponsive property relationships, self ...
Hoogenboom, Richard, Schlaad, Helmut
core +2 more sources
Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer
Advanced Functional Materials, EarlyView.Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero +12 more
wiley +1 more source
Beilstein Journal of Organic Chemistry, 2013 Sterically crowded diimine ligands with five aryl rings were prepared in one step in good yields using a micro-flow technique. X-ray crystallographic analysis revealed the detailed structure of the bulky ligands.
Shinichiro Fuse +4 more
doaj +1 more source
Novel "green" catalysts for controlled ring-opening polymerization of lactide [PDF]
, 2010 Syntéza polylaktidu (PLA) polymerací za otevření kruhu cyklického monomeru (ROP) může být uskutečněna různými způsoby. Literatura uvádí více než 100 katalytických systémů, jejichž pomocí lze polylaktid a jiné biodegradabilní alifatické polyestery získat.
Surman, František
core
Bio‐Inspired Molecular Events in Poly(Ionic Liquids)
Advanced Functional Materials, EarlyView.Originating from dipolar and polar inter‐ and intra‐chain interactions of the building blocks, the topologies and morphologies of poly(ionic liquids) (PIL) govern their nano‐ and micro‐processibility. Modulating the interactions of cation‐anion pairs with aliphatic dipolar components enables the tunability of properties, facilitated by “bottom‐up ...
Jiahui Liu, Marek W. Urban
wiley +1 more source
Effects of sterilization on the energy-dissipating properties of balsa wood [PDF]
, 1969 Technical report on the effects of sterilization on the energy-dissipating properties of balsa wood is given. Sterilization by ethylene oxide plus heat enhances the average specific energy of balsa while plastic impregnation followed by irradiation ...
Sorkin, A. B.
core +2 more sources
Formation of bridged bicycloalkenes via ring closing metathesis [PDF]
, 1998 Ring closing metathesis may be used in the formation of small ring bicycloalkenes from monocyclic diene ...
Grubbs, Robert H., Morehead, Andrew, Jr.
core +1 more source
Deciphering Small Molecule Diffusion Parameters Across Light Responsive Polymersome Membranes
Advanced Functional Materials, EarlyView.Light‐responsive polymersomes bearing donor–acceptor Stenhouse adducts (DASAs) enable programmable control over small‐molecule transport across synthetic membranes. By systematically varying DASA density, an optimal functionalization regime is identified that maximizes light‐gated permeability.
Farzina Matubbar +7 more
wiley +1 more source
Nucleation‐Controlled Reconstruction of CuOx for Selective CO2 Electroreduction
Advanced Functional Materials, EarlyView.The ratio of oxygen vacancies (Ov) and exposed Cu2O (111)/(200) of CuOx precatalyst is modulated by nucleation control of Cu(OH)2 precursor. Low Ov ratio and high ratio of Cu2O (111)/(200) in slow‐nucleated CuOx reconstructs to high‐coordinated oxide‐derived copper (OD‐Cu) during electrochemical CO2 reduction reaction (CO2RR) and exhibits enhanced ...
Ying Ying Ch'ng +14 more
wiley +1 more source
In Situ 3D Bioprinting: Impact of Cross‐Linking on the Adhesive Properties of Hydrogels
Advanced Functional Materials, EarlyView.In situ 3D bioprinting enables the direct deposition of cell‐laden, adhesive biomaterials for on‐site tissue regeneration. This review provides a comprehensive overview of how cross‐linking influences the bioadhesive properties of hydrogels used in 3D bioprinting, highlighting cross‐linking triggers, bioadhesion mechanisms, polymer interpenetration ...
Odile Romero Fernandez +4 more
wiley +1 more source