Results 121 to 130 of about 522,424 (297)
Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai +6 more
wiley +1 more source
Background: Special features of motor games and its many benefits to the all-round development of children have drawn the attention of experts to the role of play in education, but can learning through motor games help improve maths learning in slow ...
abbasali hosseinkhanzadeh +3 more
doaj
Learning in experimental 2 x 2 games [PDF]
In this paper, we introduce two new learning models: impulse-matching learning and action-sampling learning. These two models together with the models of self-tuning EWA and reinforcement learning are applied to 12 different 2 x 2 games and their results
Reinhard Selten +2 more
core
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Sequence Matters: an Experimental Study of the Effects of Experiencing Positive and Negative Reciprocity [PDF]
This paper presents an experimental analysis of people’s behavior in situations involving both positive and negative reciprocity. The experiment implements sequences of two types of extensive form games called Punishment games and Trust games.
Giorgio Coricelli
core
Fatal Attractors in Parity Games: Building Blocks for Partial Solvers [PDF]
Attractors in parity games are a technical device for solving "alternating" reachability of given node sets. A well known solver of parity games - Zielonka's algorithm - uses such attractor computations recursively.
Huth, Michael +2 more
core
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan +8 more
wiley +1 more source

