Results 131 to 140 of about 12,871 (300)
Advanced Healthcare Materials, EarlyView.We measure the cell‐specific responses of administering infusible ECM (iECM) in acute myocardial infarction (MI) across multiple timepoints. Using single‐nucleus RNA sequencing and spatial transcriptomics, we measure macrophage activation, fibroblast remodeling, increased vascular development, lymphangiogenesis, cardioprotection, and neurogenesis ...
Joshua M. Mesfin +18 more
wiley +1 more source
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures. [PDF]
Materials (Basel), 2021 Kaliński KJ +3 more
europepmc +1 more source
Advanced Materials, EarlyView.Metal‐free carbon catalysts enable the sustainable synthesis of hydrogen peroxide via two‐electron oxygen reduction; however, active site complexity continues to hinder reliable interpretation. This review critiques correlation‐based approaches and highlights the importance of orthogonal experimental designs, standardized catalyst passports ...
Dayu Zhu +3 more
wiley +1 more source
DETERMINATION OF CUTTING TEMPERATURE WHILE MILLING TITANIUM ALLOY BY FACE MILLS
Journal of Mechanical Engineering the National Technical University of Ukraine "Kyiv Polytechnic Institute", 2016 В работе приведен анализ особенностей процесса высокоскоростного резания, которое главным образом связывают с температурой резания в зависимости от скорости резания. Вместе с тем, показано, что в зависимости от конструкции и размеров инструмента основной критерий снижения температуры резания не всегда характеризирует высокоскоростную обработку ...
openaire +4 more sources
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies. [PDF]
Materials (Basel), 2021 Chuchala D +5 more
europepmc +1 more source
Advanced Materials, EarlyView.Drawing inspiration from the layered hard‐soft architecture found in sea sponges, this work establishes a new framework for architected cementitious composites (ACC) through multi‐material additive manufacturing (MMAM) process. The integration of mortar and elastomer phases into layered architectures enables synergistic toughening mechanisms, including
Aimane Najmeddine +5 more
wiley +1 more source
Study of a face stepped milling cutter for finishing flat surfaces
Технічна інженеріяThe paper presents the results of an experimental study on the influence of cutting force components on machining quality during finish face milling of the grey cast iron GCI21 (similar to EN-GJL-200) using a specially developed face stepped milling ...
H.M. Vyhovskyi, M.M. Plysak, Y.O. Koval
doaj +1 more source
Advanced Materials, EarlyView.The engineering of colloidal nanocrystals with complex compositions has emerged as a highly active area of research within nanomaterials science. This review covers key aspects of colloidal solid‐solution nanocrystal formation using pulsed laser irradiation.
Marina T. Candela +4 more
wiley +1 more source
Influence of Tooth Surface Geometry on Bending Fatigue Life of Face Gear
Jixie chuandong, 2015 Based on the coordinate transformation and meshing theory,the tooth surface equation of face gear is deduced.The finite element model of the different parameters（pressure angle,modulus）of face gear transmission is built,the influence of tooth face ...
Yan Hongzhi +3 more
doaj
Phase Engineering of Nanomaterials (PEN): Evolution, Current Challenges, and Future Opportunities
Advanced Materials, EarlyView.This review summarizes the synthesis, phase transition, advanced characterization spanning ex situ to in situ and operando techniques, and diverse applications of phase engineering of nanomaterials (PEN). It further outlines key challenges and future opportunities, such as phase stability, architecture control, and artificial intelligence (AI)‐driven ...
Ye Chen +7 more
wiley +1 more source