A probabilistic model for the high cycle fatigue behaviour of cast aluminium alloys subject to complex loads [PDF]
, 2013 Lien vers la version éditeur: http://www.sciencedirect.com/science/article/pii/S0142112312002472This article is dedicated to the high cycle fatigue behaviour of cast hypo-eutectic Al–Si alloys and in particular the AlSi7Cu05Mg03 alloy.
PESSARD, Etienne +3 more
core +1 more source
An indentation fatigue strength law
Philosophical Magazine Letters, 2010 Indentation fatigue, where a cyclic load is applied on the sample via an indenter, emerges as an alternative approach for measuring the fatigue properties of materials. We have carried out indentation fatigue tests on a poly(vinyl chloride) (PVC) bulk material, as well as on TiN and NiP films/coatings deposited on SUS304 steel substrates, and ...
Baoxing Xu, Akio Yonezu, Xi Chen
openaire +1 more source
Effect of Corrosion on the High Cycle Fatigue Strength of Martensitic Stainless Steel X12CrNiMoV12-3 [PDF]
, 2012 This paper addresses the effects of corrosion on the high cycle fatigue (HCF) strength of a high mechanical strength martensitic stainless steel (X12CrNiMoV12-3) that is used in aeronautic applications. HCF tests (between 105 and 107 cycles) were carried
PALIN-LUC, Thierry +4 more
core +1 more source
Evolution of surface integrity of turning TA19 titanium alloy end face under low cycle fatigue
Journal of Aeronautical Materials, 2021 The purpose of this paper was to reveal the evolution law and mechanism of surface integrity parameters of TA19 titanium alloy end face, and to provide a basis for the process control of blisk surface integrity.
DING Xiaocen +5 more
doaj +1 more source
ON THE LAW OF DISTRIBUTION OF THE RATE OF FATIGUE FRACTURE
Spravochnik. Inzhenernyi zhurnal, 2021 The article discusses the correction of the law of development of fatigue cracks based on the application of the Fokker–Planck–Kolmogorov equation. The coefficient of variation of the fatigue crack propagation rate was chosen as the correction criterion. Its decrease brings the descriptions of the fatigue fracture process closer to engineering.
openaire +1 more source
Influence of woven ply degradation on fatigue crack growth in thin notched composites under tensile loading [PDF]
, 2010 This paper deals with the fatigue of the through the-thickness crack propagation in thin notched composite laminates made of two glass woven plies. It highlights the different crack growths between warp and weft directions of the woven ply.
Barrau, Jean-Jacques +3 more
core +1 more source
Safe structural design for fatigue and creep using cyclic yield strength [PDF]
, 2014 This study proposes cyclic yield strength (CYS, σ_cy) as a potential characteristic of safe design for structures operating under fatigue and creep conditions.
Gorash, Yevgen, Mackenzie, Donald
core +3 more sources
Comparison between defects and micro-notches in multiaxial fatigue – The size effect and the gradient effect [PDF]
, 2009 Lien vers la version éditeur: http://www.sciencedirect.com/science/article/pii/S0142112308002156This paper attempts to improve the understanding of the multiaxial high cycle fatigue response of micro sized stress concentrations or notches of different ...
MOREL, Franck, NADOT, Yves, MOREL, Anne
core +1 more source
Evaluation of residual stress relaxation and its effect on fatigue strength of AISI 316L stainless steel ground surfaces: Experimental and numerical approaches [PDF]
, 2013 This paper is aimed at evaluating the residual stress relaxation and its effect on the fatigue strength of AISI 316L steel ground surfaces in comparison to electro-polished surfaces.
SIDHOM, Habib +2 more
core +1 more source