Results 101 to 110 of about 321,155 (295)
A Review of Using Few-Mode Fibers for Optical Sensing
IEEE Access, 2020 The development of few-mode fiber (FMF) has found numerous interesting applications in optical sensing. Given the remarkable capabilities of FMF, optical sensors of novel functionalities can be deployed.
Islam Ashry +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Heterogeneous 12-Core 4-LP-Mode Fiber Based on Trench-Assisted Graded-Index Profile
IEEE Photonics Journal, 2017 We design a heterogeneous 12-core 4-LP-mode fiber having two different types of cores and trench-assisted graded-index profiles. For the optimum design of the index profiles of these two heterogeneous cores, we first investigate the impacts of various ...
Jun Ho Chang +3 more
doaj +1 more source
Birefringence and polarisation mode-dispersion in spun single-mode fibres
, 1981 A theoretical and experimental analysis of the polarization properties of twisted single-mode fibers is presented. It is shown that whereas a conventionally twisted fiber possesses considerable optical rotation, a fiber which has a permanent twist ...
Bucaro +11 more
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Selective wavelength conversion in a few-mode fiber
Optics Express, 2019 We experimentally demonstrate a means to selectively enhance wavelength conversion of WDM channels on a 100 GHz grid exploiting nonlinear effects between the spatial modes of a few mode fiber. The selectivity of parametric gain is obtained by dispersion design of the fiber such that the inverse group velocity curves of the participating modes are ...
Omar F. Anjum +9 more
openaire +4 more sources
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
LCoS-based mode shaper for few-mode fiber
Optics Express, 2013 Spatial light modulation can be used to address specific fiber modes, as required in mode-division multiplexed systems. We theoretically compare phase-only spatial light modulation to a combination of amplitude and phase spatial light modulation in terms of insertion loss and crosstalk for a fiber supporting 11 LP modes.
Johannes, von Hoyningen-Huene +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source