Results 111 to 120 of about 321,155 (295)

Simultaneous Beat-Length Measurement of a Polarization-Maintaining Few-Mode Fiber

open access: yesIEEE Photonics Journal, 2019
Based on the polarization interference technique, we propose a modified method for simultaneously measuring the beat length of all guided modes in a polarization-maintaining few-mode fiber (PM-FMF).
Yaping Liu   +5 more
doaj   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

open access: yesAdvanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland   +5 more
wiley   +1 more source

Microstructured cladding elements to enhance performance and flexibility of large mode area leakage channel fibers

open access: yes
Large mode area fibers are imperative for scaling up the average power of fiber lasers. Single-mode behavior and low FM loss are the crucial functionalities for these fibers.
Baskiotis, C.   +3 more
core   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

open access: yesAdvanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm   +5 more
wiley   +1 more source

Generation of High-Quality Cylindrical Vector Beams from All-Few-Mode Fiber Laser

open access: yesPhotonics
Transverse mode control of laser intracavity oscillation is crucial for generating high-purity cylindrical vector beams (CVBs). We utilized the mode conversion and mode selection properties of two-mode long-period fiber gratings (TM-LPFGs) and two-mode ...
Pingping Xiao   +4 more
doaj   +1 more source

Twist Sensor Based on Long Period Grating and Tilted Bragg Grating Written in Few-Mode Fibers

open access: yesIEEE Photonics Journal, 2018
A twist sensor based on a few-mode long period grating (LPG) and a tilted fiber Bragg grating (TFBG) is proposed and demonstrated. The LPG, inscribed in a step index few-mode fiber by a CO2 laser, is utilized to excite the LP11 core mode.
Kang Yang   +5 more
doaj   +1 more source

Investigation of Oxygen‐Free Wetting Behavior of Aluminum on Copper via Molecular Dynamics Simulations and Experiments

open access: yesAdvanced Engineering Materials, EarlyView.
The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu   +8 more
wiley   +1 more source

Comparative Research on Mode Permutation Strategies in Mode-division Multiplexing Systems

open access: yesGuangtongxin yanjiu
【Objective】Mode-division multiplexing is a key technology to break through the capacity limit of single-mode fiber systems. In the few-mode fiber links, the pulse broadening caused by intermodal dispersion increases the complexity of multiple-input ...
GAO Tianyu   +4 more
doaj  

All-fiber few-mode interference for complex azimuthal pattern generation

open access: yesScientific Reports
We report on an all-fiber setup capable of generating complex intensity patterns using interference of few guided modes. Comprised by a few-mode fiber (FMF) spliced to a multimodal interference (MMI) fiber device, the setup allows for obtaining different
Josué I. Gómez-Méndez   +5 more
doaj   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy