Results 31 to 40 of about 236,033 (259)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Hollow core fiber with an octave spanning bandgap [PDF]
, 2010 We thoroughly compare the out-of-plane bandgaps generated by three realistic two-dimensional lattices: a triangular and a square arrangement of holes and a triangular arrangement of rods.
Poletti, Francesco, Francesco Poletti
core +1 more source
Single mode low-NA step index Yb-doped fiber design for output powers beyond 4kW
, 2022 Paper 100830ZFiber amplifiers are representing one of the most promising solid state laser concepts, due to the compact setup size, a simple thermal management and furthermore excellent beam quality.
Beier, F. +10 more
core +1 more source
Supercontinuum generation in submicrometer diameter silica fibers
Optics Express, 2006 Silica nanowires provide strong mode confinement in a cylindrical silica-core/air-cladding geometry and serve a model system for studying nonlinear propagation of short optical pulses inside fibers. We report on the fiber diameter dependence of the supercontinuum generated by femtosecond laser pulses in silica fiber tapers with average diameters in the
Rafael R, Gattass +3 more
openaire +2 more sources
Mode field diameter preserving fiber tapers [PDF]
Optics Letters, 2011 An approach for preserving the mode field diameter (MFD) in fiber tapers is demonstrated. The approach utilizes concentric dual-core fibers, which couple light from an inner core to an outer core through a taper. Fibers with a 6 μm MFD feedthrough and a 15 μm polarization maintaining feedthrough are demonstrated experimentally.
Noordegraaf, Danny +5 more
openaire +2 more sources
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source