Results 91 to 100 of about 109,242 (281)

Impact of Sustainable Binders Based on Lignin and Collagen on the Volume Stability and Mechanical Properties of MgO‐C Refractories with MgO‐C Recyclates

Advanced Engineering Materials, EarlyView.
Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller, Florian Kerber, Kirsten Moritz, Steffen Dudczig, Konstantin Kraushaar, Thomas Schemmel, Jana Hubálková, Patrick Gehre, Christos G. Aneziris   +8 more
wiley   +1 more source

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

Advanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang, Annett Wollmann, Thomas Gimpel, Alfred P. Weber   +3 more
wiley   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May, Finn‐Lennard Janthur, Lena Kreie, Michael Müller, Sarah Seffer, Nick Schwarz, Jörg Hermsdorf, Thomas Hassel, Stefan Kaierle, Ludger Overmeyer   +9 more
wiley   +1 more source

Incorporation of Selenium into Sol–Gel‐Derived Bioactive Glass: Influence on Glass Structure, Bioactivity, and its Selective Cytotoxicity

Advanced Engineering Materials, EarlyView.
Selenium was incorporated into a sol–gel‐derived bioactive glass to enable sustained therapeutic ion release. The selenium‐containing glass preserved bioactivity while selectively inducing cytotoxicity in osteosarcoma cells and maintaining osteoblastic viability.
Breno Rocha Barrioni, Thalita Marcolan Valverde, Talita Martins, Guilherme Mattos Jardim Costa, Alfredo Miranda de Goes, Marcello Rosa Dumont, Eduardo Henrique Martins Nunes, Marivalda de Magalhães Pereira   +7 more
wiley   +1 more source

Performance Analysis of Four Wave Mixing: A Non-Linear Effect in Optical fibers

International Journal of Computer Applications, 2014
Linear effects in Optical fibers are caused due to the refractive index of the optical medium's dependence on the intensity of light. One of the prominent non-linear effects in Optical fibers is the Four-wave mixing (FWM) phenomenon. FWM effect is resonant when the phase matching condition is satisfied.
Monica Bhutani, Devan Bhalla
openaire   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Non-invasive stratigraphic analyzes of gelatine-based modern painting materials with linear and nonlinear optical methods

JPhys Photonics
Stratigraphic analyzes of polychrome surfaces, such as paintings, often need samples to offer consistent results regarding the sequence and composition of the layers.
Diego Quintero Balbas, Laura Maestro-Guijarro, Paula María Carmona-Quiroga, Mohamed Oujja, Marta Castillejo, Francesca Bettini, Simone Porcinai, Jana Striova   +7 more
doaj   +1 more source

Numerical Exploration of Thermal Shock Resistance in MgO–C Refractories

Advanced Engineering Materials, EarlyView.
A mesostructure‐resolved numerical framework is developed to evaluate the thermal shock resistance of MgO–C refractories. By modeling interface debonding under rapid temperature changes and introducing a modified thermal shock parameter that accounts for mesocracks, the study shows how graphite content and aggregate size influence thermal shock ...
Jishnu Vinayak Gopi, Stephan Roth, Christos G. Aneziris, Bjoern Kiefer   +3 more
wiley   +1 more source