Results 141 to 150 of about 15,067 (255)

Highly Versatile Real‐Time Optical Noise Filtering Through Temporal Cloaking

open access: yesLaser &Photonics Reviews, EarlyView.
Conventional bandpass filtering strategies may be insufficient for recovering optical waveforms under extremely noisy conditions. We demonstrate a temporal‐cloaking denoising strategy enabled by the temporal Talbot effect, which concentrates the coherent signal of interest into short temporal slots while broadband noise remains temporally spread.
Majid Goodarzi   +5 more
wiley   +1 more source

Exploring Thermal and Mechanical Strains During Laying Down Process in Fused Filament Fabrication

open access: yesMacromolecular Materials and Engineering, EarlyView.
This study analyzes strain evolution and thermal behavior during FFF of PLA using strain gauges and infrared imaging. Microstrain levels depend on printing conditions, with adhesion‐induced compression during cooling and peak strains in early layers. Microtomography shows minimal porosity, while thermal imaging reveals rapid heat penetration, strong ...
Boubakeur Mecheri   +3 more
wiley   +1 more source

Novel Sulfur‐Rich Polymers from Inverse Vulcanization as Functional Building Blocks for Photonics

open access: yesMacromolecular Rapid Communications, EarlyView.
Isopropenyl aromatic comonomers, in particular novel 2,7‐diisopropenylfluorene and 2,8‐diisopropenyldibenzothiophene, synthesized by sustainable, facile, single‐step SMCCR from available brominated substrates are exploited in the Inverse Vulcanization process to obtain functional Sulfur‐rich macromolecular materials.
Raimondo Insogna   +7 more
wiley   +1 more source

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

open access: yesPolymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei   +3 more
wiley   +1 more source

Photonic realization of the relativistic Kronig-Penney model and relativistic Tamm surface states

open access: yes, 2011
Photonic analogues of the relativistic Kronig-Penney model and of relativistic surface Tamm states are proposed for light propagation in fibre Bragg gratings (FBGs) with phase defects.
A.F. Young   +34 more
core   +1 more source

Unlocking Klockmannite: Formation of Colloidal Quasi‐2D CuSe Nanocrystals and Photo‐Physical Properties Arising From Crystal Anisotropy

open access: yesSmall, EarlyView.
Thiol‐free hot injection approach yields quasi‐2D klockmannite CuSe nanocrystals, specifically nanosheets and uniform triangular nanoplatelets. This study reconsiders the klockmannite from the point of view of crystal anisotropy and demonstrates its effect on plasmonic response in the near‐infrared spectral region with the theoretical emergence of ...
Urvi Parekh   +10 more
wiley   +1 more source

Record‐Low Compressibility in [N(C2H5)3CH3]FeCl4 Expands Phase Engineering Horizons in Hybrid Molecular Ferroelectrics

open access: yesSmall, EarlyView.
High‐pressure studies of the lead‐free hybrid organic–inorganic ferroelectric [N(C2H5)3CH3]FeCl4 demonstrate record low compressibility, establishing it as the least compressible molecular ferroelectric known. In situ diamond anvil cell experiments identify halide selection and inorganic sublattice tuning as key compressibility controls, advancing ...
Takeshi Nakagawa   +11 more
wiley   +1 more source

Upconversion Photoluminescence to Monitor Local Heat Release During Femtosecond Direct Laser Writing of Bioinks In Situ

open access: yesSmall Methods, EarlyView.
Upconversion nanoparticle photoluminescence was used to quantify heat burden during femtosecond direct laser writing of bioinks in real time. Transient temperature spikes above 120–140°C demonstrate the need for a stringent process optimization, and fast 20 µm/s scan speeds were established to maintain physiological conditions.
Amirbahador Zeynali   +2 more
wiley   +1 more source

Home - About - Disclaimer - Privacy