The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene : 6. the properties of injection moulded long fibre PP at high fibre content [PDF]
, 2005 The results of an investigation of the mechanical performance of injection moulded long glass fibre reinforced polypropylene with a glass fibre content in the range 0-73 weight % are presented. The composite modulus exhibited a linear dependence on fibre
Thomason, J.L.
core +4 more sources
The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene : 7. interface strength and fibre strain in injection moulded long fibre PP at high fibre content [PDF]
, 2007 The mechanical performance of injection moulded long glass fibre reinforced polypropylene with a glass fibre content in the range 0-73% by weight has been investigated.
Thomason, J.L.
core +4 more sources
The influence of fibre length, diameter and concentration on the strength and strain to failure of glass fibre-reinforced polyamide 6,6 [PDF]
, 2008 Results of an investigation of the mechanical performance of injection moulded long glass fibre-reinforced polyamide 6,6 composites are presented. The glass fibre content in these composites was varied over the range 10-50% by weight using fibres with ...
Thomason, J.L.
core +4 more sources
The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene: 5. Injection moulded long and short fibre PP [PDF]
, 2002 We present results of a step by step comparison of the mechanical performance of injection moulded 'long' (LF-PP) and 'short' (SF-PP) previous termglass fibre-polypropylenenext term compounds.
Thomason, J.L.
core +4 more sources
A technique for the measurement of reinforcement fibre tensile strength at sub-millimetre gauge lengths [PDF]
, 2001 The strength of composite reinforcement fibres is normally measured on samples of much greater length than the actual residual fibre lengths found in many composite materials.
Kalinka, G., Thomason, J.L.
core +4 more sources
Analisi dell’anisotropia microstrutturale in materiali compositi rinforzati con fibre corte
Fracture and Structural Integrity, 2013 Synchrotron light microtomography has proved to be particularly efficient in order to analyze the microstructural characteristics in terms of reinforce fibre distribution and orientation in glass fibre reinforced composites. The spatial distribution of
A. Bernasconi, F. Cosmi, D. Dreossi
doaj +3 more sources
Lagrangian tracking of fibres in a channel flow [PDF]
EPJ Web of Conferences, 2019 Tracking of fibres in a fluid flow is much more complicated than tracking of spherical particles. In fibre motion, the orientation of fibre against the flow direction plays a very important role. In addition to the standard equation of motion, additional
Volavy Jaroslav +4 more
doaj +1 more source
Applied Sciences, 2022 The diagnostics of constructions built with steel fibre reinforced concrete are extremely difficult to conduct because, typically, no information on the actual amount and orientation of the fibres is available.
Simon Cleven +2 more
doaj +1 more source
On the influence of the rheological boundary conditions on the fibre orientations in the production of steel fibre reinforced concrete elements; pp. 408–413 [PDF]
Proceedings of the Estonian Academy of Sciences, 2016 In this paper the influence of the boundary conditions on the fibre orientation distribution in rheology simulations of the casting of steel fibre reinforced concrete is discussed.
Heiko Herrmann, Aarne Lees
doaj +1 more source
Characterization of continuous Hibiscus sabdariffa fibre reinforced epoxy composites
Polymers and Polymer Composites, 2022 The influence of fibre orientation on physical, mechanical and dynamic mechanical properties of Hibiscus sabdariffa fibre composites has been studied.
Atik Mubarak Kazi, Ramasastry DVA
doaj +1 more source