Results 61 to 70 of about 1,592 (195)

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Motor models for field oriented control

, 1992
Tese de mestr.. Dissertation submitted for obtain the degree of Master of Electronic and Computer Engineering at the University of Porto, Faculty of Engineering. Faculdade de Engenharia. Universidade do Porto. 1992
openaire   +2 more sources

Direct torque control versus indirect field-oriented control of induction motors for electric vehicle applications

Engineering Science and Technology, an International Journal, 2020
Performance and energy efficiency of induction motors (IM) used in electric vehicle (EV), by applying two control methods, namely the indirect field-oriented control (IFOC) method and the direct torque control (DTC) method, are compared.
Mustafa Aktas, Khaled Awaili, Mehrdad Ehsani, Aydemir Arisoy   +3 more
doaj   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

Design of an adaptive PI speed controller for FOC-driven underwater thrusters

Brodogradnja
Underwater thrusters are the primary actuators in marine vehicles. The thruster drive and control methods for these thrusters considerably influence their dynamic response, accuracy, and efficiency.
Kaicheng Shen, Caoyang Yu, Jinrong Zheng, He Zhang, Xianbo Xiang, Lian Lian   +5 more
doaj   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

PASTA‐ELN: Simplifying Research Data Management for Experimental Materials Science

Advanced Engineering Materials, EarlyView.
Research data management faces ongoing hurdles as many ELNs remain complex and restrictive. PASTA‐ELN offers an open‐source, cross‐platform solution that prioritizes simplicity, offline access, and user control. Its in tuitive folder structure, modular Python add‐ons, and open formats enable seamless documentation, FAIR data practices, and easy ...
S. Brinckmann, G. Winkens, R. Schwaiger
wiley   +1 more source