Results 61 to 70 of about 897,227 (298)

UAV flight control system based on STM32F4 and FreeRTOS

Hangkong gongcheng jinzhan
The high-performance CPU is taken as processors and Vxworks is taken as the design kernels for most flight control systems, which has the problems of high cost, large size and non-disclosure of kernel source code.
ZHOU Zhiguang, XU Mengmeng, SHI Meilin, LI Qingyuan, WANG Fan   +4 more
doaj   +1 more source

An Automatic Thrust Calculation Method in Case of Engine Gear Missing in Flight Control Simulation System [PDF]

Xibei Gongye Daxue Xuebao, 2018
The paper proposes an automatic thrust calculation method in the case of engine gear missing. The trimmed linearization method is used to calculate the equivalent throttle opening between the two gears. An automatic thrust calculation method is presented

doaj   +1 more source

An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials

Advanced Engineering Materials, EarlyView.
An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut, Pierre Le Berre, Hamdi Jaballah, Lukas Fink, Victor Poline, Richard Haettel, Stéphane Grenier, Gilbert Chahine, Ewen Bellec, Guillaume Buatier, Wilfried Hortschitz, Santa Pile, Thomas Schrefl, Nils Blanc, Yuan Hong, Thibaut Devillers, Nora M. Dempsey   +16 more
wiley   +1 more source

Aeroservoelastic analysis method for mixed-command fault of flight control system

Hangkong gongcheng jinzhan
Large civil aircraft fly-by-wire flight control systems may experience a fault condition where both normal mode and direct mode control commands are output simultaneously. It is necessary to propose a method to demonstrate the airworthiness compliance of
DING Luning, YANG Fei, LI Peng
doaj   +1 more source

AFTI/F-16 digital flight control system experience [PDF]

, 1984
The Advanced Flighter Technology Integration (AFTI) F-16 program is investigating the integration of emerging technologies into an advanced fighter aircraft.
Mackall, D. A.
core   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source

Biodegradable and Recyclable Luminescent Mixed‐Matrix‐Membranes, Hydrogels, and Cryogels based on Nanoscale Metal‐Organic Frameworks and Biopolymers

Advanced Functional Materials, EarlyView.
The study presents biodegradable and recyclable mixed‐matrix membranes (MMMs), hydrogels, and cryogels using luminescent nanoscale metal‐organic frameworks (nMOFs) and biopolymers. These bio‐nMOF‐MMMs combine europium‐based nMOFs as probes for the status of the materials with the biopolymers agar and gelatine and present alternatives to conventional ...
Moritz Maxeiner, Julian Burkhart, Kateryna Borysova, Chiara Mazzariol, Klaus Müller‐Buschbaum   +4 more
wiley   +1 more source

MOFs and COFs in Electronics: Bridging the Gap between Intrinsic Properties and Measured Performance

Advanced Functional Materials, EarlyView.
Metal‐organic frameworks (MOFs) and covalent organic frameworks (COFs) hold promise for advanced electronics. However, discrepancies in reported electrical conductivities highlight the importance of measurement methodologies. This review explores intrinsic charge transport mechanisms and extrinsic factors influencing performance, and critically ...
Jonas F. Pöhls, R. Thomas Weitz
wiley   +1 more source

In Situ 3D Bioprinting: Impact of Cross‐Linking on the Adhesive Properties of Hydrogels

Advanced Functional Materials, EarlyView.
In situ 3D bioprinting enables the direct deposition of cell‐laden, adhesive biomaterials for on‐site tissue regeneration. This review provides a comprehensive overview of how cross‐linking influences the bioadhesive properties of hydrogels used in 3D bioprinting, highlighting cross‐linking triggers, bioadhesion mechanisms, polymer interpenetration ...
Odile Romero Fernandez, Mulazim Hussain Asim, Shumaila Arshad, Gergely Kali, Andreas Bernkop‐Schnürch   +4 more
wiley   +1 more source

Interfacial and Crystallographic Regulation of Zinc Anode via Electric Double Layer Reconstruction for Highly Stable Zn Anode

Advanced Functional Materials, EarlyView.
Trace amounts of perfluoro‐1‐butanesulfonyl fluoride enables the regulation of the Zn/electrolyte interface by the generated zincophilic ─SO3H groups with long hydrophobic ─CF2 tails, which adsorb strongly onto the Zn surface, displace water molecules from the inner Helmholtz plane, and reconstruct the electrical double‐layer structure.
Dinesh Patel, Yimei Chen, Ashwini Kumar Sharma, Xiaolei Wang   +3 more
wiley   +1 more source