Results 101 to 110 of about 1,761,220 (302)
Slotted test section dynamics of the NTF [PDF]
A dynamic model of the National Transonic Facility (NTF) section and plenum chamber was developed. The model serves as a means for determining the dynamic performance of the NTF and the subsequent design of optimal control configurations, and is of one ...
Gumas, G.
core +1 more source
Setup‐Optimized Sequencing in Job Shops: Modeling Workstation Productivity and Lateness Behavior
Advanced Engineering Materials, EarlyView.Setup‐optimized sequencing in job‐shop production creates a trade‐off between productivity improvement and schedule reliability. A WIP‐explicit modeling framework links sequencing‐induced productivity gains and lateness dispersion through the production operating curve.
Friederike Stefanowski +2 more
wiley +1 more source
Research on flow characteristics of aerostatic circular thrust bearing
The Journal of Engineering, 2018 In order to improve the pressure distribution, the aerostatic circular thrust bearing with single supply hole was studied. In the computational fluid dynamics (CFD) simulation, the laminar model, the turbulent model, the mixture model of laminar and ...
Hechun Yu +4 more
doaj +1 more source
Three-dimensional simulation of cavitating flow in real journal bearing geometry [PDF]
, 2014 This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the ...
4th Micro and Nano Flows Conference (MNF2014) +4 more
core
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
BioengineeringThe flow and heat transfer of a steady, viscous biomagnetic fluid containing magnetic particles caused by the swirling and stretching motion of a three-dimensional cylinder has been investigated numerically in this study.
Jahangir Alam +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source