Results 31 to 40 of about 73,500 (284)

Ultralow friction and wear of reciprocating systems lubricated by liquid crystalline fluids

, 2022
S.409-416Tribological systems that are lubricated with liquid crystals exhibit ultralow friction coefficients and wear. This effect, which has not yet been well examinated and which is even less understood, has been reproducibly observed in reciprocating
Janietz, D., Kailer, A., Amann, T., Konrath, G., Sawade, H.   +4 more
core   +1 more source

Effect of Micro-Textured Surfaces and Sliding Speed on the Lubrication Mechanism and Friction-Wear Characteristics of CF/PEEK Rubbing against 316L Stainless Steel under Seawater Lubrication

Applied Sciences, 2021
In this work, the lubrication mechanism and friction-wear characteristics of the friction pair between carbon-fiber-reinforced polyether ether ketone (CF/PPEK) and 316L stainless steel with a micro-hemispherical pit textured surface at different sliding ...
Yingna Liang, Jianxin Gao, Dianrong Gao, Yanan Sun, Zongyi Zhang, Jianhua Zhao   +5 more
doaj   +1 more source

High-temperature wear performance and mechanism of NM400/NM500 mining machinery steels

工程科学学报, 2019
The friction and wear behavior of NM400 and NM500 steels in the temperature range from room temperature to 300℃ were investigated, including the formation of interface oxide, wear surface morphology, and microstructures.
HUANG Xia-xu, SHEN Yan-hua, JIN Shun-yao, SHI Bo-qiang   +3 more
doaj   +1 more source

Sliding wear of a-C:H coatings against alumina in corrosive media [PDF]

, 2013
This paper reports the results obtained from the study of friction and sliding wear in two corrosive solutions of an a-C:H coating deposited on 316L stainless against an alumina ball, employed as static counter part. Calculations of the values of the von
La Barbera Sosa, J.G., PUCHI-CABRERA, Eli-Saul, IOST, Alain, Santana Mendez, Y.Y., PUCHI-CABRERA, E.S., CHICOT, Didier, CHICOT, D., van Gorp, A., SANTANA, Y.Y., VAN GORP, Adrien, Carrasquero, E.J., Iost, A., STAIA, M.H., Puchi-Cabrera, Eli Saúl, CARRASQUERO, E., LA BARBERA-SOSA, J.G., Santana-Mendez, Y.Y.   +16 more
core   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Tribological characteristics of Al–Mg–Si–Cu alloy against die steel under elevated temperatures in simulated hot extrusion environment

Journal of Materials Research and Technology
Friction is a considerable boundary condition in aluminum alloy hot extrusion. In this study, ball-on-disc friction tests at temperatures of 25–500 °C were performed to equivalently simulate the interface tribological behaviors between Al–Mg–Si–Cu alloy ...
Zhiwen Liu, Ming Zhang, Ping Yan, Xiao Liu, Luoxing Li   +4 more
doaj   +1 more source

Friction and Wear Behavior of 201HT Cast Aluminum Alloy with Various Competitive Material

Archives of Foundry Engineering, 2017
The friction and wear properties of 201HT aluminum alloys and the corresponding competitive coupons were tested on an electrohydraulic servo face friction and wear testing machine (MM-U10G).
Li R., Chen L. J., Su M., Zeng Q., Li H., Liu Y.   +5 more
doaj   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

On the Thermodynamics of Friction and Wear―A Review [PDF]

Entropy, 2010
An extensive survey of the papers pertaining to the thermodynamic approach to tribosystems, particularly using the concept of entropy as a natural time base, is presented with a summary of the important contributions of leading researchers.
Amiri, Khonsari
openaire   +2 more sources