Results 41 to 50 of about 73,500 (284)
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
FrictionA traction steel belt is a key load-bearing and transmission component that replaces traditional steel wire rope to achieve an elevator friction drive. Under actual operating conditions, when an elevator slips due to unexpected factors such as emergency ...
Xiuheng Zhang +3 more
doaj +1 more source
Effect of molding process on tribological characteristics of friction materials based on resin
工程科学学报, 2017 Resin transfer molding (RTM) and hot-pressing molding (HPM) were used to prepare phenolic resin matrix composites reinforced by carbon fiber. The tribological properties of the materials were tested using a MS-T3001-type friction and wear tester.
LI Hui +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji +3 more
wiley +1 more source
Lubricants, 2022 The tribological behavior of graphene as an additive in a water-based nanofluid lubricant was investigated using pin-on-disk tests on titanium alloy (Ti-6Al-4V) and cemented tungsten carbide (WC–Co) contacts.
Chris Goralka +6 more
doaj +1 more source
Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids
Advanced Functional Materials, EarlyView.This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow +9 more
wiley +1 more source
Advances in Sustainable and Wearable Textile Based Soft Robotics
Advanced Functional Materials, EarlyView.This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas +6 more
wiley +1 more source
Fenmo yejin jishuThe friction properties and heat resistances of the iron-copper based powder metallurgy friction materials were tested by MM3000 friction and wear testing machine under 7 continuous braking conditions.
MA Ling +6 more
doaj +1 more source
Effect of Experimental Parameters on Wear Response of Thermally Sprayed Carbide Based Coatings [PDF]
Materials Research, 2018 Friction and abrasive wear response of WC-12 Co and Cr3C2-25 NiCr coatings was studied. Abrasive wear experiments were conducted with SiC abrasive particles with varying load and sliding speeds.
Nitesh Vashishtha, Sanjay Sapate
doaj +2 more sources
Advanced Functional Materials, EarlyView.Collagen II coatings support the formation of synovial fluid nanofilms, while collagen I coatings do not. Both bind recombinant equine lubricin similarly. These findings may help explain articular cartilage surface joint dysfunction, inform biomaterial design for synovial joint repair, and expand on lubricin‐based osteoarthritis therapies.
Diego R. Jaramillo Pinto +12 more
wiley +1 more source