Results 121 to 130 of about 506,862 (302)
Friction and morphology of magnetic tapes in sliding contact with nickel-zinc ferrite [PDF]
Friction and morphological studies were conducted with magnetic tapes containing a Ni-Zn ferrite hemispherical pin in laboratory air at a relative humidity of 40 percent and at 23 C.
Bhushan, B., Buckley, D. H., Miyoshi, K.
core +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
EnergiesA solar air heater (SAH) converts solar energy into heated air without causing environmental pollution. It features a low initial cost and easy maintenance due to its simple design.
Byeong-Hwa An +3 more
doaj +1 more source
Tsunami Prone Friction Factors From Wind Measurements
Coastal Engineering 1980, 1980 The long wave equations, used for tsunami run-up and flood wave calculations, have an unknown friction term. As an alternative to hydraulically determined friction factors, an adjustable three-level anemometer staff system is used for making wind profile measurements over typical Hawaii terrain.
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich +3 more
wiley +1 more source
Journal of the South African Institution of Civil Engineers, 2010 New and extensive results are reported on the flow of a range of non-Newtonian fluids, including aqueous suspensions of bentonite and kaolin, and aqueous solutions of synthetic polymer carboxymethyl cellulose (CMC), flowing down inclined flumes of ...
R Haldenwang, P T Slatter, R P Chhabra
doaj
Numerical Exploration of Thermal Shock Resistance in MgO–C Refractories
Advanced Engineering Materials, EarlyView.A mesostructure‐resolved numerical framework is developed to evaluate the thermal shock resistance of MgO–C refractories. By modeling interface debonding under rapid temperature changes and introducing a modified thermal shock parameter that accounts for mesocracks, the study shows how graphite content and aggregate size influence thermal shock ...
Jishnu Vinayak Gopi +3 more
wiley +1 more source
Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release
Advanced Engineering Materials, EarlyView.Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro +3 more
wiley +1 more source
In-flight Compressible Turbulent Boundary Layer Measurements on a Hollow Cylinder at a Mach Number of 3.0 [PDF]
Skin temperatures, shearing forces, surface static pressures, and boundary layer pitot pressures and total temperatures were measured on a hollow cylinder 3.04 meters long and 0.437 meter in diameter mounted beneath the fuselage of the YF-12A airplane ...
Gong, L., Quinn, R. D.
core +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source