Results 111 to 120 of about 484,215 (304)

Evaluation of the Mechanical and Tribological Behavior of Polyether Ether Ketone Fiber-Reinforced Resin-Based Friction Materials Fabricated by Wet Granulation. [PDF]

Polymers (Basel), 2023
Li L, Ma Z, Liu G, Song W, Ren L, Yuan S, Yang X, Zhang Q, Ma Y.   +8 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Effect of Polymer Ether Ketone Fibers on the Tribological Properties of Resin-Based Friction Materials. [PDF]

Materials (Basel), 2023
Li L, Ma Z, Liu G, Tong J, Song W, Ren L, Tong T, Ma Y.   +7 more
europepmc   +1 more source

Eco-efficient friction materials [PDF]

, 2013
Automotive friction materials are multi component composites in which fibrous materials play a fundamental role. Modern friction formulations have been developed around asbestos fibres, a heavily used material before legislation outlawed its use in the ...
Sloan, Michael Sloan
core  

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Tribological Behavior of Friction Materials of a Disk-Brake Pad Braking System Affected by Structural Changes-A Review. [PDF]

Materials (Basel), 2022
Ilie F, Cristescu AC.
europepmc   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Study on microstructure and property of typical copper-based brake pads

Fenmo yejin jishu
To address the issues of low friction coefficient, poor stability, and high wear of the traditional copper-based brake pads under high-temperature braking conditions, the copper-based brake pads were prepared by high temperature solid-phase hot-pressing ...
DIWU Xiaofei, CHEN Wenge, OUYANG Fangming   +2 more
doaj   +1 more source

Friction-Wear Characteristics of Carbon Fiber Reinforced Paper-Based Friction Materials under Different Working Conditions. [PDF]

Materials (Basel), 2022
Ma Z, Zheng C, Xiong C, Yu L, Liu Y, Zhang C.   +5 more
europepmc   +1 more source

Tribological properties of polymer films and solid bodies in a vacuum environment [PDF]

The tribological properties of ten different polymer based materials were evaluated in a vacuum environment to determine their suitability for possible lubrication applications in a space environment, such as might be encountered on the proposed space ...
Fusaro, Robert L.
core   +1 more source