Results 51 to 60 of about 91,325 (216)

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

A Transient Model for Fuel Cell Cathode-Water Propagation Behavior inside a Cathode after a Step Potential

Energies, 2010
Most of the voltage losses of proton exchange membrane fuel cells (PEMFC) are due to the sluggish kinetics of oxygen reduction on the cathode and the low oxygen diffusion rate inside the flooded cathode.
Der-Sheng Chan, Kan-Lin Hsueh
doaj   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source

Microstructure Modification of Additively Manufactured Mo–9Si–8B by Annealing and Its Effects on High‐Temperature Mechanical Properties

Advanced Engineering Materials, EarlyView.
Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt, Yong Chen, Georg Hasemann, Benjamin Wahlmann, Carolin Körner, Manja Krüger   +5 more
wiley   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Investigation and optimization of a PEM fuel cell’s electrical and mechanical behavior [PDF]

Hydrogen, Fuel Cell & Energy Storage, 2016
Effect of clamping pressure on electrical resistance between Gas diffusion layer (GDL) and bipolar plate is a very important parameter in Proton exchange membrane (PEM) fuel cells.
Mostafa Habibnia, Mohsen Shakeri, Salman Nourouzi, Peyman Ghasemi Tamami   +3 more
doaj   +1 more source

Self‐Cleaning Sensor Surfaces for Long‐Term Environmental Monitoring

Advanced Engineering Materials, EarlyView.
Long‐term use of unattended outdoor sensors without soiling or biofouling is achieved through generation of a micro‐ and nanorough cuvette surface by combing hydrophobic nanoparticles with fluorinated polymers, crosslinked and surface‐attached through CHic chemistry. The coating demonstrates self‐cleaning behavior and prolonged outdoor stability, which
Sanam Kumari Rajak, Yasmina Frey, Ulrike Wallrabe, Oswald Prucker, Jürgen Rühe   +4 more
wiley   +1 more source

Impact of gas diffusion layer architecture on the performances of Cu-based electrodes for CO2 electroreduction to ethylene in flow reactors

Journal of CO2 Utilization
Electrocatalytic CO2 reduction reaction (CO2RR) is a promising strategy to convert CO2 into fuels and building blocks for chemicals, exploiting renewable energy sources.
Marco Etzi, Julien Dangbegnon, Angelica Chiodoni, Candido F. Pirri   +3 more
doaj   +1 more source

Development of portable DMFC system with low water crossover MEA

Nihon Kikai Gakkai ronbunshu, 2014
This paper describes inner-water circulation DMFC (Direct Methanol Fuel Cell) system with low water cross-over MEA (Membrane Electrode Assembly). Water permeation controlled layer which has lower permeability (K~10 -14 m 2) than conventional micro porous
Ryosuke YAGI, Yuusuke SATO, Masato AKITA, Takuya HONGO, Norihiro TOMIMATSU   +4 more
doaj   +1 more source

Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy

Advanced Engineering Materials, EarlyView.
Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang, Jianxiang Zhao, Zhaoqi Chen, Hao Gong, Yinsen Yan, Junlei Tao, Yong Yang   +6 more
wiley   +1 more source