Results 11 to 20 of about 3,099,875 (176)

Effect of torch angle on arc properties and weld pool shape in stationary GTAW [PDF]

open access: yes, 2013
In this paper, a three dimensional numerical simulation is performed on a stationary arc to study the effect of torch angle in gas tungsten arc welding (GTAW) of SS304 stainless steel.
Parvez, Shahid   +4 more
core   +4 more sources

Investigation of a ceramic metal matrix composite functional surface layer manufactured using gas tungsten arc welding [PDF]

open access: yes, 2014
Wear resistant surfaces with high toughness and impact resistant properties are to be created to improve the life cycle cost of brake discs for trains. A potential solution to this industrial problem is to use an arc cladding process.
Herbst, Stephan
core   +4 more sources

Effect of different electrode tip angles with tilted torch in stationary gas tungsten arc welding : A 3D simulation [PDF]

open access: yes, 2013
In this study, the effect of different tip angles (30°, 60°, 90° and 120°) on the arc and weld pool behaviour is analysed in 2mm and 5mm arc lengths with tilted (70°) torch.
Parvez, Shahid   +2 more
core   +4 more sources

Derivation of forces acting on the liquid weld metal based on arc pressure measurements produced using alternating shielding gases in the GTAW process [PDF]

open access: yes, 2013
As part of an ongoing process to fully evaluate the effects of an alternating shielding gas supply on the gas tungsten arc and gas metal arc welding processes, a comparison between arc pressures produced using argon, helium, alternating gases and GTAW-P ...
Campbell, Stuart   +2 more
core   +3 more sources

A computational fluid dynamic analysis of the effect of weld nozzle geometry changes on shielding gas coverage during gas metal arc welding [PDF]

open access: yes, 2013
Three geometry changes to the inner bore of a welding nozzle and their effects on weld quality during gas metal arc welding (GMAW) were investigated through the use of computational fluid dynamic (CFD) models and experimental trials. It was shown that an
Campbell, Stuart   +3 more
core   +4 more sources

Arc pressure and weld metal fluid flow whilst using alternating shielding gases Part 1 : arc pressure measurement [PDF]

open access: yes, 2013
As part of an ongoing process to fully evaluate the effects of an alternating shielding gas supply on gas shielded welding processes, a comparison between the arc pressures generated using argon, helium, alternating shielding gases and pulsed GTAW has ...
Campbell, Stuart   +2 more
core   +4 more sources

Residual stress evaluation in API 5L X65 girth welded pipes joined by friction welding and gas tungsten arc welding

open access: yesJournal of Materials Research and Technology, 2019
The present study compared the residual stress states in friction welded pipes of API 5L X65 to those achieved by gas tungsten arc welding (GTAW). X-ray diffraction (XRD) was used to assess residual stresses.
Carlos Alexandre Pereira de Moraes   +4 more
doaj   +1 more source

A Study on the Corrosion Behavior in Sea Water of Welds Aluminum Alloy by Shielded Metal Arc Welding, Friction Stir Welding and Gas Tungsten Arc Welding

open access: yesInternational Journal of Electrochemical Science, 2015
Three types of welds aluminum alloy 6061 were prepared using shielded metal arc welding (SMAW), friction stir welding (FSW) and gas tungsten arc welding (GTAW). In addition for the first time borax powder was used with GTAW in weld region to increase the
Mustafa Özgür ÖTEYAKA, Hamdi AYRTÜRE
doaj   +1 more source

On arc efficiency in gas tungsten arc welding [PDF]

open access: yesSoldagem & Inspeção, 2013
The aim of this study was to review the literature on published arc efficiency values for GTAW and, if possible, propose a narrower band. Articles between the years 1955 - 2011 have been found. Published arc efficiency values for GTAW DCEN show to lie on a wide range, between 0.36 to 0.90.
openaire   +3 more sources

The differential analysis for temperature distribution diagnostics of arc current-carrying region in sheet slanting tungsten electrode inert gas welding with the electrostatic probe

open access: yesHigh Temperature Materials and Processes, 2021
An electrostatic probe differential analysis method is used to diagnose the arc current-carrying region of the sheet slanting tungsten electrode.
Li Yuanbo   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy