Results 1 to 10 of about 1,162 (70)

Distribution of SiC particles in semisolid electromagnetic-mechanical stir-casting Al-SiC composite [PDF]

open access: yesChina Foundry, 2018
The distribution of SiC particles in Al-SiC composite can greatly influence the mechanical performances of Al-SiC composite. To realize the homogeneous distribution of SiC particles in stir-casting Al-SiC composite, semisolid stir casting of Al-4.25vol.
Yun-hui Du, *Peng Zhang, Wei-yi Zhang
doaj   +1 more source

Electrodeposition of High-Quality Ni/SiC Composite Coatings by Using Binary Non-Ionic Surfactants

open access: yesMolecules, 2023
In order to increase the hardness, wear resistance and corrosion resistance of nickel-based coatings, pure nickel is often co-electrodeposited with silicon carbide (SiC) particles.
Han Rao   +6 more
doaj   +1 more source

The introduction of SiC into Cu melts based on Ti–SiC system and its transformation

open access: yesJournal of Materials Research and Technology, 2020
In this work, SiC particles with different sizes have been effectively introduced into Cu melts based on Ti–SiC system, and the types and microstructures of Ti–SiC reaction products are varied with the SiC size change. With small size, SiC can absolutely
Qing Liu   +5 more
doaj   +1 more source

Impact of Silicon Carbide Particles Weight Percentage on the Microstructure, Mechanical Behaviour, and Fractography of Al2014 Alloy Composites

open access: yesAdvances in Materials Science and Engineering, 2022
The microstructure, mechanical characteristics, and tensile fractography of Al2014 alloy reinforced composites with 5 and 10% wt. % of 150 to 160 micron-sized SiC particles were investigated in this study.
H. S. Vasanth Kumar   +6 more
doaj   +1 more source

Effect of Necklace-Type Distribution of SiC Particles on Dry Sliding Wear Behavior of As-Cast AZ91D/SiCp Composites

open access: yesCrystals, 2020
In this study, the dry sliding wear behaviors of SiC particle reinforced AZ91D matrix composites fabricated by stirring casting method were systematically investigated. The SiC particles in as-cast composites exhibited typical necklace-type distribution,
Chao Sun   +5 more
doaj   +1 more source

Microstructure and mechanical properties of nanoscale xSiC/Mg‒5.5Zn‒0.1Y alloys by solid phase synthesis

open access: yesFenmo yejin jishu, 2023
The Mg‒5.5Zn‒0.1Y alloys reinforced by the nanoscale SiC particles were prepared by solid phase synthesis, and the effect of SiC particle mass fraction on the microstructure and mechanical properties of Mg‒5.5Zn‒0.1Y alloys was investigated.
PENG Erbao, MA Xiao
doaj   +1 more source

Differentiation in the SiC Filler Size Effect in the Mechanical and Tribological Properties of Friction-Spot-Welded AA5083-H116 Alloy

open access: yesFibers, 2022
Ceramic reinforced friction stir spot-welding (FSSW) is one of the unique welding techniques used to fabricate spot joints. This study is intended to investigate the effect of reinforcement additive particle size in achieving higher weld strengths ...
S. Suresh   +3 more
doaj   +1 more source

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

open access: yesJournal of Materials Research and Technology, 2023
The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy
Xinghua Ji   +7 more
doaj   +1 more source

Fabrication and Sc-Refinement of SiCp/A356 Composites by Vacuum Stirring Casting Method

open access: yesJournal of Electrical and Computer Engineering, 2022
Aluminum matrix composites reinforced with 10 vol.% SiC particles (SiCp/Al MMCs) were prepared throughthe vacuum stirring method from SiC particles preoxidated at high temperature, followed by posttreatments of remelting and Sc addition treatment.
Fukun Chen, Kuangfei Wang
doaj   +1 more source

Effect of particle size and weight fraction of SiC on the mechanical, tribological, morphological, and structural properties of Al-5.6Zn-2.2Mg-1.3Cu composites using RSM: fabrication, characterization, and modelling

open access: yesHeliyon, 2022
Stir-casting was employed to create Al-5.6Zn-2.2Mg-1.3Cu composites with particle sizes ranging from 30 to 90 μm and a weight fraction of 5–15 SiC articles. The mechanical and wear properties of the material have been assessed. The wear-behaviour of Al-5.
Ravinder Kumar   +7 more
doaj   +1 more source

Home - About - Disclaimer - Privacy