Densification and Mechanical Properties of 439L Steel Composites Blended with Fifteen Micron-Size Silicon Carbide Particles [PDF]
439L stainless steel composites blended with fifteen micron SiC particles were prepared by uniaxial pressing of raw powders at 100 MPa and conventional sintering at 1350oC for 2 h.
Sang Woo Lee +2 more
doaj +1 more source
Microstructure and mechanical properties of aluminium based nanocomposites strengthened with alumina and silicon carbide [PDF]
Al-Al₂O₃ and Al-4wt%Cu-SiC metal matrix nanocomposites were studied because these materials have a potential for offering good ductility, high strength, and high electrical and/or thermal conductivity, which make them ideal for engineering applications ...
Gazawi, Amro Abdul-Karim
core
Effect of addition of SiC particles on the Microstructure and Hardness of Al-SiC composite [PDF]
This work aims to investigate the effect of the addition of silicon carbide particles on the microstructure and the hardness of the Al-SiC metal matrix composites.
Kallimani, Anilkumar S +7 more
core +1 more source
Electrodeposition of Ni-Co/Nano SiC Composites from a Citrate Bath and their Characterization
The electrodeposition of Ni-Co/nano SiC composites onto steel substrates from a citrate bath was carried out under different experimental conditions. The addition of SiC to the bath increased the overvoltage for the Ni-Co alloy deposition. The morphology
M.M. Kamel +5 more
doaj +1 more source
Copper matrix composites reinforced with nano-Al2O3 particles and micro-SiC whiskers were prepared. Nano-Al2O3 particles are uniformly dispersed in the copper matrix (Figure a), and there is an obvious amorphous transition layer at the interface between ...
Lin Huanran +5 more
doaj +1 more source
Electrocodeposition of Ni composites and surface treatment of SiC nano-particles [PDF]
This work has explored the surface modification of SiC submicron- and nanoparticles, and its influence on the particles' chemical behaviour and deposition rate in the electroplating of composite Ni/SiC coatings. SiC particles with different sizes (50, 60,
C. Zanella +11 more
core +1 more source
Effect of friction stir processing (FSP) on microstructure and hardness of AlMg10/SiC composite [PDF]
The AlMg10 aluminum alloy reinforced with SiC particles was subjected to friction stir processing (FSP). The composite was made by mechanical mixing and gravity casting. The mass fraction of SiC particles in the composite was about 10%. Evaluation of the
J. Iwaszko, K. Kudła
doaj +1 more source
In present study, copper powders (Cu) and silicon carbide (SiC) particles were used to produce Cu-adhered SiC particles (Cu/SiC), which were used to reinforce Fe-based matrix materials to modify properties.
Wubin Jin, Yongmin Zhou
doaj +1 more source
Study on Performance of Co-W/SiC Composite Coatings Electrodeposited on Copper
In this paper, CoW/SiC composite coatings were electrodeposited from plating bath with various nano SiC concentrations. The effect of SiC concentrations on deposition rate, hardness, corrosion resistance and surface morphology of CoW/SiC coatings were ...
KangNing Zhao +3 more
doaj +1 more source
EFFECT OF HEAT TREATMENT ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF EXTRUDED SiC/6061 COMPOSITE
The effect of heat treatment on microstructure and mechanical properties of extruded SiC/6061 aluminium alloy matrix composite was investigated. The heat treatment (annealing at 540 °C for 1.5 hours, water quenching and artificial aging at 170 °C for 7 ...
Miroslav Glogovsky +4 more
doaj +1 more source

