Results 11 to 20 of about 1,507,093 (110)

The Electrostatic Induction Characteristics of SiC/SiC Particles in Aero-Engine Exhaust Gases: A Simulated Experiment and Analysis

open access: yesAerospace
This study investigates the electrostatic induction characteristics of silicon carbide-fiber-reinforced silicon carbide (SiC/SiC) particles within aero-engine exhaust gases using a dedicated J20 turbojet engine experimental platform.
Yan Liu   +5 more
doaj   +2 more sources

Nucleation and growth mechanism of Ni/SiC composite coatings electrodeposited with micro- and nano-SiC particles

open access: yesJournal of Materials Research and Technology
To study the nucleation and growth mechanism of Ni/SiC composite coatings, electrodeposition was conducted in the Ni bath containing SiC particles with different sizes.
Han Rao   +5 more
doaj   +2 more sources

The Influence of Coating Oxide Metal on Surface of SiC Particles to Elastic Modulus of Al/SiC Composites

open access: yesMakara Seri Sains, 2008
The isotropic composites of Al/SiC is made by powder metallurgy method, the quality of mechanical materials depend on interfacial bonding between matrix (Al) and reinforcement (SiC).
Dedi Priadi   +3 more
doaj   +1 more source

Investigation of a ceramic metal matrix composite functional surface layer manufactured using gas tungsten arc welding [PDF]

open access: yes, 2014
Wear resistant surfaces with high toughness and impact resistant properties are to be created to improve the life cycle cost of brake discs for trains. A potential solution to this industrial problem is to use an arc cladding process.
Herbst, Stephan
core   +4 more sources

NiP/SiC composite coatings: the effects of particles on the electrochemical behaviour [PDF]

open access: yes, 2005
NiP/SiC (17 at.% P) composite coatings were prepared by electrodeposition from a Brenner type plating bath containing SiC particles. Cyclic voltammetry and immersion time were used to evaluate the electrochemical behaviour of these coatings.
Zoppas Ferreira, J.   +19 more
core   +1 more source

Heat Treated NiP–SiC Composite Coatings: Elaboration and Tribocorrosion Behaviour in NaCl Solution [PDF]

open access: yes, 2009
Tribocorrosion behaviour of heat-treated NiP and NiP–SiC composite coatings was investigated in a 0.6 M NaCl solution. The tribocorrosion tests were performed in a linear sliding tribometer with an electrochemical cell interface.
Bonino, Jean-Pierre   +9 more
core   +1 more source

Investigating the Microstructure, Tensile Strength, and Acidic Corrosion Behaviour of Liquid Metal Stir Casted Aluminium-Silicon Carbide Composite

open access: yesAdvances in Materials Science and Engineering, 2023
The main objective of this investigation is to study the microstructural features and evaluate the tensile strength, hardness, and acidic corrosion resistance of liquid metal stir casted aluminium-silicon carbide (Al-SiC) composite.
S. Prathap Singh   +6 more
doaj   +1 more source

Characterization of Aluminum Alloy–Silicon Carbide Functionally Graded Materials Developed by Centrifugal Casting Process

open access: yesApplied Sciences, 2021
The continuous development of modern industries rises the necessity for functionally graded materials. This research starts from the consideration that the incorporation of SiC particles in the molten aluminum alloy can be difficult due to the very low ...
Ioan Milosan   +7 more
doaj   +1 more source

Lubricated sliding wear behaviour of aluminium alloy composites [PDF]

open access: yes, 2005
Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates.
Rainforth, W.M., Jones, H., Walker, J.C.
core   +1 more source

Effect of the surface adsorbate of SiC particles on fabrication and mechanical property of aluminum matrix composite

open access: yesCailiao gongcheng, 2019
SiCp/Al composites were prepared by pressureless infiltration using domestic abrasive grade SiC particles with average diameters in the range of 60-80μm.
CUI Yan   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy