Results 191 to 200 of about 137,006 (311)
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
DEM [Discrete Element Method] simulations of drained and undrained behaviour
, 2008 This thesis reports the results of DEM (Discrete Element Method) simulations of the behaviour of granular material for axisymmetric compression and plane strain deformation under both drained and undrained conditions. The aim is to study the behaviour of
Gong, Guobin
core
A Simplified Calibration Procedure for DEM Simulations of Granular Material Flow. [PDF]
Materials (Basel)Hajivand Dastgerdi R, Malinowska AA.
europepmc +1 more source
Friction phenomena and their impact on the shear behaviour of granular material. [PDF]
Comput Part Mech, 2017 Suhr B, Six K.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán +5 more
wiley +1 more source
The Effect of Arching on the Outflow Properties of Silos
, 2009 The outflow properties of silo’s are the most important parameters of their design. The discharge rate of granular material from silos differs from the discharge rate of containers filled with liquids (it does not depend on the filling height).
Oldal István, Keppler István
core
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source