Results 81 to 90 of about 1,633 (205)
The present review focuses on the progress of tribology from the prehistoric period to the contemporary interdisciplinary research trends. During the Paleolithic period, humans used sliding friction, generated inadvertently, to make fire. The Paleolithic
Prasanth , P. V. +5 more
core +2 more sources
ARTIFICIAL JOINTS: THEIR TRIBOLOGY AND WEAR PARTICLE ANALYSIS [PDF]
, 2008 The wear, friction, lubrication and particle distribution of differently heat treated CoCrMo cast prostheses provided by the same supplier were analysed. Wear tests were conducted on both pin-on-plate and simulation rigs.
Kinbrum, Amy
core
Multiscale Structuring of Hydroxyapatite via Two‐Photon Lithography of Nanocomposites
Advanced Functional Materials, Volume 36, Issue 36, 4 May 2026.Hydroxyapatite scaffolds are of great interest in bone tissue engineering applications, ranging from 3D cell culture to regenerative medicine. Using two‐photon lithography of a transparent nanocomposite, hydroxyapatite microstructures with features ranging from submicron to centimeter‐scale are fabricated. This allows to mimic the natural bone geometry,
Leonhard Hambitzer +6 more
wiley +1 more source
, 2015 The purpose of this issue is to explore the relationship between tribology and precision in manufacturing. The issue will cover but is not limited to nano-technology and nano-tribology.
Yousif, Belal
core
Point force in a plane in the context of fractional nonlocal elasticity
Archives of MechanicsSolutions to the point load problems for elastic solids have different applications in geomechanics, contact mechanics, tribology as well as in modeling of lattice defects in crystals.
Y. Povstenko, T. Kyrylych, A. Yatsko
doaj +1 more source
Tribological investigations of silicon nitride lubricated by ionic liquid aqueous solutions
, 2020 S.295-303Water-lubricated ceramic components are promising material combinations for tribological applications because they are wear-resistant and can exhibit low coefficients of friction under different loads.
Kailer, A., Amann, T., Kurz, J.
core +1 more source
Fiber association and network formation in PLA/lignocellulosic fiber composites. [PDF]
, 2013 PLA composites were prepared in an internal mixer with a lignocellulosic fiber having relatively large aspect ratio. Fiber content changed between 0 and 60 vol% and the homogenized material was compression molded to 1 mm thick plates.
Renner, Károly +4 more
core +1 more source
Materials FuturesThis study investigates the optimization of cermet-modified layers (CML) on Ti6Al4V titanium alloy surfaces, prepared via laser sintering-assisted nitrogen reaction followed by hot isostatic pressing (HIP) post-treatment. The laser-sintered CML exhibited
Qianqian Cheng, Jie Jin, Jun Zheng
doaj +1 more source
Engineering Science and Technology, an International Journal, 2016 Natural fiber reinforced polymer composites have emerged as a potential environmentally friendly and cost-effective alternative to synthetic fiber reinforced composites. Therefore, in the past decade, a number of major industries, such as the automotive,
Emad Omrani +2 more
doaj +1 more source
Erratum to: Green tribology: Fundamentals and future development [PDF]
Friction, 2013 [7] Nasonovsky M, Bhushan B. Green tribology. Phil Trans R Soc A 368: 4675–4676 (2010) [8] Nasonovsky M, Bhushan B. Towards the “green tribology”: Biomimetic surfaces, biodegradable lubrication, and renewable energy. In Proceedings of STLE/ASME International Joint Tribology Conference, San Francisco, 2010. [11] Nasonovsky M, Bhushan B (Eds).
openaire +1 more source