Results 231 to 240 of about 83,709 (298)

Molecular Inks for the Development of Complex 3D In‐Mold Electronics

Advanced Materials Technologies, EarlyView.
Molecular inks (MINKs) enable the fabrication of thermoformed 3D circuits by decoupling the forming and metallization steps. Following thermoforming, intense pulsed‑light or thermal processing converts the patterned MINKs into complex 3D conductive tracks with improved stretchability and electrical performance, advancing low‑cost, high‑performance in ...
Mehal P. Kushalkar, Hiroshi Fukutani, Olga Mozenson, Jianying Ouyang, Liliana Gaburici, Bhavana Deore, Dayna Bennett, Chantal Paquet, Paul Trudeau, Loleï Khoun, Nicolas Milliken, Olivier Ferrand, Julie Ferrigno, Xiangyang Liu, Arnold J. Kell   +14 more
wiley   +1 more source

Reduced switch multiple active bridge DC-DC converter for modular solid-state transformers. [PDF]

Sci Rep
Khani S, Hosseini SH, Sabahi M.
europepmc   +1 more source

Extreme‐Temperature Resistant, Flexible, and Sensitive Strain Sensor for Aerospace Parachute Deployment

Advanced Materials Technologies, EarlyView.
In this study, we report a resistive‐type strain sensor fabricated using single‐walled CNTs, are used layer using the pray technique to deposit as conductive, and UV‐resin was spin‐coated as a protection layer. The sensor functioned in harsh temperature variation conditions from −50°C to 125°C without deterioration.
Jagan Singh Meena, Lucas Lum Yu Xiang, Dhivya Dharshini Kannan, Chun Fei Siah, Yeow Kheng Lim   +4 more
wiley   +1 more source

Enhancing electrical and thermal stress capabilities of hybrid CBs in VSC based MT HVDC grids using thyristor based FCL topology. [PDF]

Sci Rep
Khan B, Yousaf MZ, Khalid S, Shakeel MA, Guerrero JM, Sivanraju R.   +5 more
europepmc   +1 more source

High‐Power Rapid Laser‐Induced Synthesis of Multi‐functional Cobalt Metal‐Organic Framework With an Unprecedented Synthesis Efficiency

Advanced Materials Technologies, EarlyView.
Laser‐assisted synthesis enables rapid (within 1 h) and high‐yield (≥90%) production of Co‐MOFs with mesoporous structures, tunable magnetic and optical properties, and efficient adsorption of N2, CH4, and CO2 for low‐energy gas separation. DFT calculations elucidate the electronic structure and adsorption behavior.
Saliha Mutlu, Bülend Ortaç, Ali Karatutlu, Taylan Gorkan, Engin Durgun, Dilek Soyler, Saniye Soylemez, Jelena Lillepäg, Volkan Filiz, Nergis Arsu, Sevil Savaskan Yilmaz   +10 more
wiley   +1 more source

Novel resilient solar photovoltaic power extraction strategy for rural AC micro grids with enhanced incremental conductance based MPPT. [PDF]

Sci Rep
Shanmugam P, Hussaini MM, Kumarasamy V, Thangavel J, Muthusamy S, Tirugatla SK, Paulsamy C, Salau AO.   +7 more
europepmc   +1 more source

A Comparative Analysis of Grid-Following and Grid-Forming Converters with HIL Validation

2025 IEEE Power & Energy Society General Meeting (PESGM)
Jesus Flores Huaman, Lucas Elias Dos Santos, Jose Carlos Ugaz, Daniel Dotta   +3 more
openaire   +1 more source

Highly Anisotropic Quasi‐Direct Organic Metal Halide Hybrids: A Platform for Polarization‐Sensitive Optoelectronics

Advanced Materials Technologies, EarlyView.
One‐dimensional C4N2H14PbBr4 is shown to have a quasi‐direct electronic band structure and strongly anisotropic transport with polarized broadband emission. A GW/Bethe–Salpeter excited‐state force formalism, supported by polarized Raman and temperature‐dependent photoluminescence, identifies low–frequency Pb–Br phonons that drive ultrafast exciton self‐
Rijan Karkee, Rafael R. Del Grande, Yeonjoo Lee, Jinkyoung Yoo, Azza Ben‐Akacha, Biwu Ma, Michael T. Pettes, David A. Strubbe   +7 more
wiley   +1 more source

Active line model identification protection based on characteristic frequency phase for dual-end weakly-fed AC system. [PDF]

Sci Rep
Hou J, Zhang Z, Fan Y, Song G, Wu X.
europepmc   +1 more source

Additive‐Manufactured, Multifunctional Bioreactor Technology for Dynamic Culture of 3D Bioprinted Tissue Models

Advanced Materials Technologies, EarlyView.
We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger, Johann Schorzmann, Hsuan‐Heng Lu, Muhammad Osama, Julian Bauer, Michael Haug, Oliver Friedrich, Aldo R. Boccaccini, Frank Döpper, Sahar Salehi   +9 more
wiley   +1 more source